Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - big iron

Pages: 1 2 [3] 4 5
31
Originality / 67 Alt. Pulley 3844100
« on: January 19, 2012, 02:46:26 AM »
Does anyone know if the 67 L78 alt. pulley 3844100 is being reproduced?
Thanks.
Bob

32
Originality / Rear Tailpipe Hanger
« on: October 14, 2011, 04:51:03 PM »
Have what is supposed to be 69 rear tailpipe hanger but does not show up in 69 P&A. # 3965633 stamped on hanger. ???
Can someone cross the number for me?
Thanks.
Bob

33
Restoration / 67 center console w / M40
« on: July 22, 2011, 02:37:29 PM »
Looking at 67 AIM  D55 A7 # 2 6293329. Does anyone know the color of the part number label used on that section of the wiring harness ?
Bob

34
Originality / 67 BB Engine Gaskets
« on: May 13, 2011, 12:51:41 AM »
I has been awhile since I put an original engine together and need help on original gasket type selection. In what areas, if any where cork gaskets used? ???
Bob

35
Originality / 67 BB Water Pump Cover
« on: May 11, 2011, 03:16:39 AM »
Can anyone remember if the rear water pump cover was plated or plain steel? Plate should have rolled edges.
Bob

36
Originality / Static Collector Asm.
« on: May 10, 2011, 04:54:44 PM »
Anyone know if the static collector asm. was used on both LH and RH hubs, or only on the LH spindle?
Refer to 67 AIM U63 A1.
Bob

37
Originality / JL 8 Dust Shields
« on: May 07, 2011, 02:38:27 AM »
Anyone know what type fastener was used to fasten the front dust shield to the caliper bracket? I have done quite a bit of research and the only mention I have heard is from the people that sell the dust shields.
Bob

38
Originality / 67 AC Blower Motor Screws
« on: January 21, 2011, 09:03:14 PM »
Need description (size,finish and head markings) of AC blower motor screws (motor to case).
Looking at 67,68,69 AIM C60 D1 what is special about SPL. WASHER 606404?
Bob

39
Originality / 68 BB AC Hose Routing Clamps and Hardware
« on: November 20, 2010, 02:08:50 AM »
Looking at 68 AIM C60 D4. Anyone have a picture of caps #8,clip #9,#10 and clamp#11? Any idea what caps #8 look like?  ???
Bob

40
Originality / 68 BB AC Clip Mounting
« on: November 20, 2010, 01:34:15 AM »
Looking at the 68 AIM C60 D5. The clip #8 is mounted to the bracket with #3,#4,#5,and #6. The bolt #3 and l washer #4 go through a threaded 5/16-24 hole just below the hole shown, then the clip #8,  l washer #5 and finely the nut #6.
Now the question. Why do they show two different lock washers being used? Is this correct?  ???
Bob

41
Restoration / 1st gen. power windows
« on: November 08, 2010, 06:28:44 PM »
Does anyone make a replacement power window regulator and motor that can be used with factory wiring? ???
Bob

42
Restoration / 67 D55 auto center console w/gauges- ground for lights
« on: October 30, 2010, 02:10:38 AM »
Looking at 67 AIM D55 A6 I can not find the existing hole in the under body that #8 ( 9419400) is suppose to screw into. I have looked all over that area and can not find a hole or dimple.
The shifter and gauge lights are grounded at this point.
Can anyone help me out with a picture or measurements?
Bob

43
Originality / 67 power feed wire
« on: October 17, 2010, 03:18:50 AM »
Anyone have a picture of the firewall piercing for the 67 power feed wire A31/C06?
Bob

44
Restoration / Need correct color shock paint
« on: October 13, 2010, 03:27:08 AM »
Does anyone know if Krylon Spar Var #KS112 Shadow Gray is still being produced? If not, what would be the best alternative?
Checked Krylon site and it shows discontinued but not sure if only one color was discontinued or the whole line. Asked about Spar Var but have had no responce.
Did CRG search but info. is 3 years old.
Bob

45
Restoration / aluminum refinishing
« on: October 06, 2010, 02:17:33 AM »
When aluminum parts, such as an alternator, are tumbled and the original finish is obtained. What happens to the original stamped numbers? I would think that the numbers would have a cast look to them. Are the numbers re-stamped to give them the shiny look.What is done to the machined surfaces to protect them from the tumbling process?
Bob

Pages: 1 2 [3] 4 5
anything