466
General Discussion / Muncie shifter change
« on: June 15, 2010, 12:47:55 AM »
Does anybody have a good idea when the shifter levers stamped "MUNCIE" were replaced with the non-stamped lever ?
Victor
Victor
News:
Welcome to the CRG Discussion Forum!
Classified ads are not allowed on the forum.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
467
Restoration / Re: Question on 67-69 Doors
« on: June 15, 2010, 12:20:29 AM »
Merv,
Check your phone messages. Call me anytime, I will be happy to help if I can. Good luck.
Victor
Check your phone messages. Call me anytime, I will be happy to help if I can. Good luck.
Victor
468
Restoration / Re: Any pictures of windshield mounting clips?
« on: June 15, 2010, 12:15:52 AM »
The screws under the cowl are short sheetmetal screws with a "M" on the socket head. The outer clip holes are right above the top door hinge bolt, it may be hidden by the end of the widow rubber coming from the roof line. These outer clips use the same screws. they can be installed in place but be careful of bending your stainless or scratching the paint. I have installed them after the stainless is in place with a pair of needle nose vicegrips, be sure to make sure the clip lands all the way into the trim before screwing them down. Another set of hands and eyes would be helpful.
Victor
Victor
470
General Discussion / Re: Opinions requested
« on: March 28, 2010, 11:45:08 PM »
Dont froget to check the padding and the springs. The failure of either probley lead to the original tear.
VT
VT
471
Restoration / 1968 reveal door ledge mouldings
« on: March 20, 2010, 02:35:14 AM »
How is the custum reveal mouldings held on? The service manual states there are screws, Where are they, and do they snap on and off ? I looked and felt for screws. . . . but i could be blind and numb.
Thanks,
Victor
Thanks,
Victor
472
Research Topics & Reports / Re: 1968 SS hood ornaments
« on: March 02, 2010, 02:24:05 AM »
O5C, 396, Stacks.
VT
VT
473
Decoding/Numbers / Re: Real tag or not?
« on: February 06, 2010, 04:26:19 PM »
Painted P T B ? First red flag.
VT
VT
474
General Discussion / Re: If you bought a car based on certification.........
« on: January 23, 2010, 07:25:39 PM »
After following this thread my "respect" for a "certified" car is gone. I never knew that they can be tilted depending on what the person paying wants to hilghight. I thought the inspection would be the same no matter what the out come was. Buyer Beware for sure!!
Victor
Victor
475
General Discussion / Re: HOW LONG HAVE YOU HAD YOUR CAR AND WHAT DID YOU PAY FOR IT ?
« on: December 11, 2009, 03:39:57 AM »
1968 RS/SS 396 4 speed in 1980 for $600.00 cash. standard black int., Black vinyl top, all #'s Except for starter, distributor and alternator, I changed those out through the early years... The originals? who knows. Car was in great condition except for a Earl Schibe $29.95 paint job and deep set 14 x 6 and 14 x 7 rusted Ansen rims. The car was repainted LeMans blue with BLACK SS stripes, New vinyl, Polished the original trim ect. over this summer.
Victor
Victor
476
Restoration / Re: 68 AIM revision Date
« on: December 11, 2009, 03:13:49 AM »
Looks like the 29th to me.
Victor
Victor
477
Restoration / Re: 68 R/S rocker trim fasteners
« on: December 11, 2009, 03:12:19 AM »
Hi guys,
I am still in need of the proper location (which hole uses which fastener) information, I did go through the Fisher book but could not find a picture or list of fastener order.
Paul, What page did you see this picture? The 68 B.B.F. book i purchased was printed AUGUST 1967 (Perfect condition for $10.00 from Louie @ the Long Beach Swapmeet) Any 68 Guys out there that remember the fastener order?
Thank you,
Victor
I am still in need of the proper location (which hole uses which fastener) information, I did go through the Fisher book but could not find a picture or list of fastener order.
Paul, What page did you see this picture? The 68 B.B.F. book i purchased was printed AUGUST 1967 (Perfect condition for $10.00 from Louie @ the Long Beach Swapmeet) Any 68 Guys out there that remember the fastener order?
Thank you,
Victor
478
Restoration / Re: 68 R/S rocker trim fasteners
« on: November 20, 2009, 04:11:48 AM »
Paul,
Thanks for the info. Will be on the look out for a copy.
VT
Thanks for the info. Will be on the look out for a copy.
VT
479
Restoration / 68 R/S rocker trim fasteners
« on: November 18, 2009, 02:26:07 AM »
Hi guys,
I need help with the correct use of the 4 different mounting fasteners. for each side there are 11 mounting holes. 3 on the front fender, 3 on the quarter panel, and the rest on the door. the AIM only shows the front fender mounting. Does any one know where I can find another picture of the mounting? I can easly mount the trim, but I want it in the correct order.
Thank you,
Victor
I need help with the correct use of the 4 different mounting fasteners. for each side there are 11 mounting holes. 3 on the front fender, 3 on the quarter panel, and the rest on the door. the AIM only shows the front fender mounting. Does any one know where I can find another picture of the mounting? I can easly mount the trim, but I want it in the correct order.
Thank you,
Victor
480
General Discussion / Re: Option ID'ing
« on: July 25, 2009, 05:06:47 AM »
Hi Guys,
I have not been able to confirm this yet but I'm thinking the Dash trim only came with a N30 or N34 Steering wheel.
Victor
I have not been able to confirm this yet but I'm thinking the Dash trim only came with a N30 or N34 Steering wheel.
Victor