Messages

46

Mild Modifications / Re: Speedo Gear Reducer

« on: November 14, 2016, 02:39:16 PM »

You can do a drive gear swap without pulling the trans. Just be careful not to let the counter shaft pin to pull out with the tail-shaft housing allowing the thrust washer to drop. If it does it can still be re-positioned just a PITA.

47

General Discussion / Re: Hurst shifters

« on: November 02, 2016, 01:57:25 PM »

What about shift ball thread size. Mine was 5/16-18. I was told they were all 3/8. What gives?

48

Originality / Re: 1111480 dist looks *real*??

« on: September 24, 2016, 12:23:16 AM »

I would need a close up of the stamp before validating.

49

Restoration / Re: 69 BB washer pump not pumping

« on: September 20, 2016, 05:34:40 PM »

Try priming it with a syringe at the reservoir. 

50

General Discussion / Re: Repro tach burned out

« on: September 12, 2016, 02:24:52 PM »

I have a Pertronix Ign. conversion on my 67 with Factory tach with no issues.
Are you wired to the Neg. post on the coil?

51

General Discussion / Re: Trying to close deal on 69 Camaro-Title Issues

« on: August 19, 2016, 05:19:18 PM »

In the case above the purchaser already has the title. Only the sellers signature needs to be notarized. I would register it in a state that is not a notary state.

52

General Discussion / Re: Trying to close deal on 69 Camaro-Title Issues

« on: August 18, 2016, 08:00:29 PM »

In Vermont there are no titles issued on vehicles over a certain age. Same in NY. So what you get is a transferable reg. that a title state will accept and issue a title upon transfer.
On the power of attorney fear what I did is list only the vehicle That the POA pertained to.
Its not a bonded title.
When I transferred. my 69 Camaro out of NY to NC all I had was the registration cert. That states on it that it is Transferable. 

53

General Discussion / Re: Trying to close deal on 69 Camaro-Title Issues

« on: August 18, 2016, 06:51:29 PM »

Try this. I do this when I have title problems or difficult people. It works, not a scam.

http://www.motorecyclenow.com/title-service.html

54

Maintenance / Re: "Flickering" speedo needle

« on: July 13, 2016, 04:33:02 PM »

If the cable is new run it around for a while and it should settle down.

55

General Discussion / Re: U17gauge package

« on: July 11, 2016, 04:18:24 PM »

If original the AC gauges should read Made In USA. The repops will have the part number only.

56

Restoration / Re: Brake distribution valve - repair or replace ???

« on: June 23, 2016, 07:45:01 PM »

Just unscrew and replace the contact.

57

General Discussion / Re: 396/375 holley 4053 jetting

« on: June 15, 2016, 05:52:41 PM »

I found 72/76 combo works best on a stock L78 or 302 with manifolds and correct exhaust.
76/76 on a cammed car with flow master and header set-up.

58

Decoding/Numbers / Re: Day one Z28 DZ

« on: June 06, 2016, 07:47:49 PM »

We will try to get the guy to remove the paint.

59

Decoding/Numbers / Re: Day one Z28 DZ

« on: June 06, 2016, 07:46:40 PM »

I read that also. It was someone who has a Numbers and docs. 69 with a Tonawanda block. Swears by it.

60

General Discussion / 67 Camaro 4K

« on: June 05, 2016, 11:32:37 PM »

http://www.ebay.com/itm/1967-Camaro-Coupe-/301976013123?vxp=mtr

http://www.yenko.net/ubbthreads/ubbthreads.php/topics/660476/mr-outlaw-67-big-block-camaro-#Post660476