61
Originality / Power brake vac. hose/69Z
« on: February 07, 2008, 02:55:34 PM »
Should the P/B vac. hose go through the spark plug wire tower or use the bracket that bolts to the rocker cover? The car is a 04C 69Z.Steve.
News:
Welcome to the CRG Discussion Forum!
Classified ads are not allowed on the forum.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
62
General Discussion / Part # needed
« on: January 23, 2008, 03:45:37 PM »
Does anyone know the current part # for the PVC hose with the molded 90 degree bend?The number in the AIM doesn't cross.Thanks,Steve.
63
Restoration / 309 Master cylinder
« on: January 15, 2008, 07:01:14 PM »
I have a 309 M/C that has some pitting in the bore.Is there anyone that rebuilds with a sleeve to correct this problem.Its original to the car so I'd like to save it.Steve.
64
Originality / 69 Cowl Induction Question
« on: January 02, 2008, 10:03:47 PM »
On a cowl ind.air cleaner assy.you have the air cleaner base then the riser ring then the flange the seal ring attaches to.My question is this,On the flange ring there is a bent lip on the inside radius,What position does this lip go?I want to install the REAR decal.Also what is the purpose of this bend?The riser ring has this bent lip that mates to the distributor dent.So that one makes sense.Thanks in advance,Steve.
65
Originality / 69 Z Question
« on: December 06, 2007, 09:45:52 PM »
Should a 69Z, X33,Dover white,Black stripes have blacked out rocker panels?
66
Restoration / Repro ZL2 set-up
« on: October 25, 2007, 05:00:28 PM »
Does anyone have an opinion(s) on the repro Cowl Induction set-up?Quality and closness to original?I have a 69Z that all is left is the wire harness for the option and I want to reinstall the remainder. Steve.
67
Originality / 69Z Cold Air Hood Option
« on: October 18, 2007, 02:41:19 PM »
Does someone have a pic.of the firewall hole location for the C/I wire harness?Also was this hole stamped or punched.I have an extra hole that was punched (metal curled inward)in the firewall and trying to figure out if it is factory or back yard engineered.
68
Originality / Correct water pump 692 or 170?
« on: October 15, 2007, 12:14:47 PM »
Which water pump would be correct for a Norwood built 04C 69 Z,170 or 692?
69
General Discussion / 69Z Camaro tail lamp question
« on: October 01, 2007, 03:25:39 PM »
What are the correct 3 bulbs for the tail lamps?In the car now are,Outer segment 1157,mid segment(reverse)1156,Inner segment 1156.The problem is the 1157 has a 3 candle power filament and the 1156 has a 25 c.p.When they are both on at the same time in park lamp position they don't match.They only match when the brakes are applyed.The lamp sockets are dual contact outer.Single contact mid.And single contact inner.so the bulbs match the sockets.Did somone switch the inner sockets from double to single or are the 1156s wrong for the inner position?
70
Restoration / 69 Camaro horn
« on: September 26, 2007, 06:32:24 PM »
Anyone know of a horn repair/restoration service.I have original dual horns in a 69Z and one is not working.
71
Decoding/Numbers / Muncie speedo gear part numbers
« on: September 25, 2007, 06:34:35 PM »
Does anyone know the part numbers for the range of drive and driven gears on the Muncie trans?Or where I can find a list?