Messages

61

Restoration / black on tailpan on ss cars

« on: July 21, 2007, 02:50:20 AM »

What is the correct color for the black tailpan on a big block SS 67 camaro.  gloss or 60%

62

Restoration / Re: oval floor pan plugs

« on: July 15, 2007, 05:35:50 PM »

thanks guys. That is what I was told, don't understand the logic, but if that is what the factory done, who am I to change.  thanks  again

63

Restoration / oval floor pan plugs

« on: July 14, 2007, 06:52:09 PM »

Does anyone certain on how the oval floor pan plugs should be installed with the indention down in the floor pan hole or with the indention up?. Logically it looks like they should go down, but I am being told that they were installed up at the factory.  On the internet I have seen both.  thanks  Pete

64

Restoration / Re: 1967 Camaro Pin Stripes

« on: July 02, 2007, 06:52:16 PM »

Now that we have established that my car should and will have the pinstripes, where do I get any pictures and measurements for the striping.  thanks guys

65

Restoration / Re: 1967 Camaro Pin Stripes

« on: July 01, 2007, 10:41:05 PM »

I want to thank everyone.  My car is a 67 SS and has the style trim group. it also has the interior trim group to include the chrome pillar mlds.  outside has the wheel well mldgs,bumble bee stripe, blacked out tail pan and molding trim at the rocker panels.  I believe the stainless mldgs at rocker panels were only RS models .  The car is going for paint this week and I will be adding the pinstripes.  again thanks.

66

Restoration / Re: 1967 Camaro Pin Stripes

« on: July 01, 2007, 06:25:45 PM »

That last piece of information is very helpful.  That is close to the same thing that I heard from another reliable source.  If anyone else has another opinion please post it.  Also, which cars recived the blacked out rocker panels? 

67

Restoration / Re: 1967 Camaro Pin Stripes

« on: July 01, 2007, 04:25:57 PM »

Do you know if your Bolereo Red car had the stripes b/c of an additional option or not?  My 67 SS 396 coupe is a non RS car and I have the original window sticker and it does not have the pin stripe listed on it.  I'm just curious if the pin stripe came along with the nose stripe. 

68

Restoration / Re: 1967 Camaro Pin Stripes

« on: July 01, 2007, 02:52:56 PM »

I believe you are right,but I have seen standard 67's also with the pinstripe. Did the factory use this stripe on the RS models only?  thanks  Pete

69

Restoration / Re: 1967 Camaro Pin Stripes

« on: July 01, 2007, 03:13:28 AM »

I believe the D96 stripes were not available for the 67 cars.  correct?.  The D96 started at the bottom of the fender well and followed up around and straight back half way the panel.  The pinstripe I am refering to is a point to start and into twin pin stripes from front to back over the fender wells and back into a point.

70

Restoration / Re: 396 intake

« on: July 01, 2007, 03:00:55 AM »

I have found the Intake I needed on ebay.  thanks  Pete

71

Restoration / Re: 1967 Camaro Pin Stripes

« on: July 01, 2007, 02:57:12 AM »

Am I understanding the RPO, D96 that only the RS and 11 cars had the pin stripes?  Thanks for the info.  Pete

72

Restoration / 1967 Camaro Pin Stripes

« on: July 01, 2007, 12:28:00 AM »

I was recently told that all 1967 Camaros that had a nose stripe also had the factory pin strip across the tops of the fenders, doors, and rear quarters.  Is this true?  Does anyone have any information, which cars had the pin stripe?

73

Restoration / 396 intake

« on: June 24, 2007, 09:21:20 PM »

I am searching for a cast iron intake for my 67 bbc camaro. The car was buile in april 67.  I need an intake from oct,nov,dec of 66 or jan 67.  My intake was august of 67 and is too new for this engine.  anyone have one, contact onebad34@hotmail.com.  thank you

74

Restoration / Re: 1967 starter

« on: June 24, 2007, 03:08:56 PM »

Sorry I didn't get any replies on my question, but I was at the GM nationals this weekend and found out the 67 camaro had a cast steel nose piece on the starter and from 68 up had the aluminum.  I am looking for a cast iron intake for this car. The one on it is too new. My car was built in march 67. I need oct,nov,dec of 66 or jan of 67.  Mine is a J of 67.  Anyone help me find the correct one.  thanks in advance

75

Restoration / 1967 starter

« on: June 14, 2007, 02:53:18 AM »

Hello, I am currently restoring a 1967 camaro. numbers matching 396/325, 4spd. question, does the starter to have a steel nose piece or aluminum?  thanks