Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - onebad34

Pages: [1] 2 3 ... 5
1
Restoration / Rear Bumperettes
« on: June 11, 2010, 09:01:55 PM »
Did every 67 Camaro without Bumper Guards get the smaller bumperettes? 

2
Restoration / 67 camaro fender
« on: February 03, 2009, 03:18:32 AM »
Still in need of a nos 67 camaro standard right fender. Any help?  thanks Pete

3
General Discussion / camaro nos fender
« on: November 16, 2008, 03:31:12 AM »
What is the basic way to tell a nos gm fender from a aftermarket. I am looking for a set of NOS fenders for a 67 camaro. I have contact with an individual who says he has a original gm fender for right side.  I am going tomorrow to look at it.  Looking for tell tale way to tell if it is GM.  thanks  Pete

4
Restoration / camaro fender
« on: November 13, 2008, 01:16:22 AM »
Looking for a 67 std camro front fender. right side, must be NOS.   email me at onenbad34@hotmail.com

5
Originality / Re: 1967 Camaro space saver spare info? N65 option
« on: October 13, 2008, 02:44:34 AM »
Why does my assembly manual show a space saver tire for the coupe and convertible on page 361, UPC N65 sheet A2 ?  Pete

6
Restoration / Re: space saver tire
« on: October 13, 2008, 02:05:23 AM »
I went out to my assembly manual and on page 361, UPC65, sheet A2, shows the mounting assy for the space saver tire for both the coupe and convertible. My car had the space saver in it and the mounting location for the bolt on a full size tire is in a different place.  I still need the canister.  Pete

7
Restoration / space saver tire
« on: October 12, 2008, 05:39:59 PM »
1967 camaro, space saver tire, are the canisters the same for 67,68,69?  I am doing a 67 bb and the car came with the space saver tire,but no canister. e-bay shows one for 68,69.  Is there a difference?  thanks  Pete

8
Restoration / camaro markings
« on: October 12, 2008, 01:54:11 PM »
I have noticed that on some of the restorations, there is an orange stripe painted vertically across the frame on the drivers side just in front of the stablilzer bar.  What did this stand for, and in what part of assemble was this put on.  thanks  Pete

9
Restoration / Radiator Tag
« on: October 11, 2008, 06:05:01 PM »
What is the exact location for the radiator tag on a 1967 BB Camaro

10
Restoration / Re: 67 camaro master cylinder
« on: September 04, 2008, 12:30:19 AM »
Thanks Steve,  That is exactly the info I was looking for.   Again thanks   Pete

11
Restoration / Re: 67 camaro master cylinder
« on: September 02, 2008, 09:01:05 PM »
The First two I purchases from Heartbeat City.  The first one I installed on the car and It leaked fluid out the back.  Called and they sent another one. Bled it on the bench and installed.  It would push fluid but would not build pressure.  Took off car and disassembled and found the tubing used to sleeve had a seam. Took the first one apart and it also was sleeved with seamed tubing.  They did not have another one.  sent back.  Met individual at Carlisle from Correct Systems and he sent me a master cylinder with the casting no of 5460346 with a WT stamp on the front.  He stated he bench bled and it works fine.  I did not bench bleed this one, installed on the car and when I went to hook up the lines, noticied the port sizes were reversed.  This one has the larger fitting on the front and the smaller on the back. Opposite of the first two, which My lines did hook up to.  I notified indiv. and am waiting for a response.  I was trying to verify the correct casting no for a 67 camaro, power disc/drum brake car.  Any info will be appreciated.  Pete

12
Restoration / 67 camaro master cylinder
« on: August 30, 2008, 02:07:40 AM »
I have a dilema, We are still attempting to finish up the breakes on this camaro.  We are on our third mastercylinder, the first two would not build pressure.  We have now received another one, but for some reason beyond my knowledge, the size of the ports are reversed.  On the first two the larger fitting was on the back and the smaller fitting was on the front.  The first two fit and plumbed up to the correct lines on the car. This new one the size of the fittings are reversed.  The casting no. is      5460346 with a wt code. Should be correct. Any info is needed.  thanks in advance  Pete

13
Restoration / Re: 67 camaro rear glass
« on: July 02, 2008, 09:03:47 PM »
John, I totally agree. Our intent was to use the 80# sand bags and add appox 250 lbs that way to have the front end aligned.  I thought that would be better than leaning over the new paint work, also the adjustment on the upper A arm is more accessible.  Do you thing this will work.  Pete

14
Restoration / Re: 67 camaro rear glass
« on: July 01, 2008, 10:07:21 PM »
To SAURON327. Scott B.   We received the rear window today.  Need less to say, We are very pleased with the glass.  It fits perfect  and my son said he was going to call you personally. It is great to have fellow car buffs that are willing to help each other.  It is also great that CRG has this website so we can connect with each other to help with parts or troubleshooting.  One problem solved, one to go.  We are waiting for the third MC for the car, hopefully we will have breakes, then get front end aligned, then bolt on the front end. Once we get the parts, we should be able to complete the car in a week or two.  Once again , special thanks to SAURON327,   Thanks Scott.    Keep in touch.    Pete

15
Restoration / Re: Pressure relief valve
« on: June 26, 2008, 12:23:51 AM »
Hey thanks for the info.  I went on line and you can see the difference between the 67/68 part no. PR114, and the one listed for the 69, part no. PR 105,  I will be ordering one in the morning.  Thanks again and I will keep you posted.   Pete

Pages: [1] 2 3 ... 5