Messages

46

Originality / Re: Chambered exhaust hanger

« on: November 12, 2010, 11:48:58 PM »

Ok now the big problem does anyone sell just that hanger and reinforcment piece? I bought a complete set and misplaced the 2 hangers at the border when customs checked my parts.

47

Originality / Re: Chambered exhaust hanger

« on: November 12, 2010, 08:02:48 PM »

As always help as soon as I asked. Thanks guys

48

Originality / Chambered exhaust hanger

« on: November 12, 2010, 01:26:59 PM »

Anyone have a good picture of the exhaust hanger that supports the chambered pipe just before it goes up and over the rear axle. Not sure were this hanger bolts to the car. Thanks

49

Originality / Re: 1968 Tail pipes

« on: October 31, 2010, 01:24:29 AM »

Yes that is what I have seen on some of the dars I have looked at.

50

Originality / 1968 Tail pipes

« on: October 30, 2010, 06:12:08 PM »

Does anyone know if the tail pipes on a 68 z were slash cut on an angle were the exhaust exits the system?

51

Originality / Re: cowl plenum

« on: October 26, 2010, 10:06:42 PM »

I think they have a built in washer 

52

Originality / Re: cowl plenum

« on: October 25, 2010, 03:13:32 PM »

Thanks Jerry ,you are a great guy to share your knowledge on these cars. Thanks once again Paul Bruce

53

Originality / Re: cowl plenum

« on: October 25, 2010, 02:24:01 PM »

I seen that car but when I try and blow the picture up it becomes distorted.

54

Originality / Re: cowl plenum

« on: October 24, 2010, 07:55:51 PM »

I did see that picture and then I looked at cars at Carlisle and some of them had a small hex screw holding the duct. I cant make out the picture of Jerrys white car to see what is on that car.Thanks again   

55

Originality / cowl plenum

« on: October 23, 2010, 04:54:15 PM »

When a cowl plenum was purchased did the screws to attach the duct to the firewall come in the package also. I have seen different types of screws used. What is correct. thanks as always.

56

Restoration / Re: 1968 smog manifolds

« on: October 21, 2010, 11:07:21 PM »

I can not seem to pull it up on the site

57

Restoration / 1968 smog manifolds

« on: October 21, 2010, 10:48:52 PM »

Anyone know the thread size for a smog fitting on a 68 Z. I need to run a tap through to clean up my thread to put smog tubes in.

58

Maintenance / Chambered on 68 Z28

« on: September 28, 2010, 04:19:05 PM »

Will a 1969 chambered exhaust system work on a 68 car? Does anyone make the correct turn down tailpipes for the chambered systems. I know it was never available from the factory but I enjoy my Z for what it was meant for. Thanks

59

Originality / Re: 68 Z28 01B- Which water-pump bypass, the hex or square head?

« on: July 19, 2010, 11:59:26 AM »

I put a square one on my 02E car. I did see the same picture in my book. Who knows GM may have ran out of stock at one time and maybe changed over from a hex to square fitting for a short while. I am sure they would not stop building cars if they ran short on one small part.

60

General Discussion / Re: Thanks to CRG team and members

« on: July 11, 2010, 07:30:17 PM »

Yes I would have lost a lot of money on phony parts if not for the help from this site. It does not matter the question someone always has a great answer on THIS site. Thanks to all  Paul