Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - fireZ

Pages: 1 ... 3 4 [5] 6 7
61
General Discussion / First generation camaro shops in vegas
« on: April 04, 2008, 08:14:43 PM »
Are there any first gen. camaro suppliers in the vegas area. Thanks

62
Originality / 1968 Z28 vavle covers
« on: April 04, 2008, 07:18:20 PM »
I looked at a set of what are suppose to be original 68 Z valve covers. I cannot remember what side the O was stamped from on these covers. The ones I looked at were stamped from the bottom side . My car is in storage so I can not get a look at the covers on it being they are original without question. Thanks

63
General Discussion / CE block
« on: March 28, 2008, 06:33:45 PM »
I looked at a 68 Z28 this morning with a CE block in it. The fellow that has the car is in his mid 60s and said the engine was replaced after the original froze and cracked one cold winter. My question is the car is a 02E car of 1968 and the CE block has a casting date of September 67 date code,so is the CE block way to early for this car?

64
General Discussion / Under dash courtesy lights
« on: February 24, 2008, 08:41:51 PM »
Which 1968 camaros had the under dash courtesy lights ? thanks

65
General Discussion / 1967 pace cars
« on: January 22, 2008, 08:38:48 PM »
Is there any chance a list of VINs exists for the 1967 pace cars.  I a looking at a car that is being represented as a pacer.

66
Originality / 1968 z28 speedo clips
« on: January 06, 2008, 09:38:30 PM »
I am doing some detail work on my 68 Z28.I can see were 2 speedo cable clips are but all the suppliers say 3 are required per car. I can see one located about 2 inches from were the cable exits the firewall and the other one is in the trans tunnel. Where would I look for the third clip?

67
Restoration / 68 Z tailpipe hangers
« on: December 23, 2007, 08:29:52 PM »
On the rear  tailpipe hangers there is 4 holes to mount to the frame. Question is assembly manual shows only 2 bolts are used to attach to car frame. Whats correct?

68
Originality / 68 Z28 centre Drag Link
« on: December 20, 2007, 02:47:10 PM »
My 68 Z has a 1.125 inch centre link and I am looking at another 68 Z with the smaller drag link. My question is did all 68 Zs not have the larger drag link or was it an option?

69
Restoration / Correct exhaust clamps
« on: December 10, 2007, 02:18:06 PM »
Anyone know the correct exhaust clamps used on a 68 Z28? Who sells the correct ones?

70
General Discussion / protecto plates book
« on: December 03, 2007, 03:34:43 PM »
I look at POPs at car shows and see some that say Printed in USA and others that say Litho in USA. What is correct for the booklets?

71
Restoration / Installing front bumper guards
« on: December 03, 2007, 01:05:30 PM »
I am installing front bumper guards on a buddies 68 camaro and I need to know some measurements. Anyone have measurements on were they install on the lower valance? Thanks

72
Restoration / 1968 front bumper guards
« on: December 02, 2007, 02:34:27 PM »
Anyone know what colour the mount bracket is suppose to be on a front bumper guard? Thanks

73
Decoding/Numbers / Numbers on cross member
« on: November 21, 2007, 02:56:33 PM »
I have started the teardown of my 68 Z and after some light cleaning I found the same # in 2 areas of my car. First on the trans cross member and also underneith the dash by the gas pedal but higher. The numbers are 27-355. They are very hard to see but are the same. Now the car is a LA car and it was a 02E car with a S355 stamping also on the Trim Tag in the top right corner. any thoughts? Thanks for any help.

74
Restoration / Steering coupler
« on: November 15, 2007, 02:27:39 PM »
I recieved a new steering coupler yesterday and I am going to install it today. My question is do the 2 plastic bushings that come on the line up pins stay on when I install the coupler to the steering shaft? They look like they will take up some play but I have never installed one before to know if I keep them on for install.  Thanks Paul

75
General Discussion / Camaro suppliers in Erie Penn. area
« on: November 11, 2007, 09:14:56 PM »
I am in the Erie Penn. area this week and wondered if anyone knows of any suppliers in the area. Thanks

Pages: 1 ... 3 4 [5] 6 7
anything