16
General Discussion / Cowl plenum
« on: June 29, 2010, 02:30:04 PM »
Does anyone make the correct cowl plenum lid in steel. I have seen fiberglass but I require a steel lid. Thanks
News:
Welcome to the CRG Discussion Forum!
Classified ads are not allowed on the forum.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
17
General Discussion / Carlisle Motels
« on: May 18, 2010, 09:00:41 PM »
Any ideas what are the best motels for close proximity to the fairgrounds at Carlisle. Never been before but thinking of going to Nationals at end of June
18
Maintenance / setting my timing
« on: April 22, 2010, 07:24:21 PM »
I have tried to set the timing on my 68 z at 4 BTC but the car will not run. I put the timing to 9-10 BTC and the car runs great,also total timing is at 32 at 2900 rpm . Any ideas why it will not run at the recommended 4BTC 
19
Maintenance / John Z vacuum seyup
« on: April 16, 2010, 07:27:53 PM »
Does anyone have a picture of John Z vacuum setup. My 302 is running alright and I was wondering about doing Johns setup on the car. Do I need to do any other changes when I do the vacuum setup John suggests
20
General Discussion / 68 Z28 car
« on: March 13, 2010, 06:19:04 PM »
I have been degreasing a 302 that is in a car I dragged home in January. Let me know what you think of the numbers as maybe or maybe not being original to the car.Car is a 02D car 678 block with casting A88 ,carb is a holley 4053 dated 705 ,alt. 1100814 dated 8B12 ,it does have correct crank but rusty,dist.1111266 dated7G20 heads are 3917291 dated L 12 7. Oh ya engine is tighter than any motor I have tried to unc Thanksease
21
Restoration / crank pulley bolts
« on: November 17, 2009, 03:14:16 PM »
Anyone know what size the bolts are that attach the crank pulley to the harmonic balancer on a 68 Z28. Thanks Paul
22
Restoration / 68 Z intake bolts
« on: October 28, 2009, 08:49:09 PM »
Going through a lot of old engine hardware. Anyone know what size the intake bolts were and thread size for aluminum intake on 302 car?
23
Maintenance / 1968 302 rocker arms
« on: October 27, 2009, 05:01:17 PM »
What rocker arms did 302 engines have 1.5 or 1.6 ?
24
Restoration / 1968 Seat belt retractors
« on: October 21, 2009, 05:12:33 PM »
Any idea what the model # was on the seat belt tags for 1968 Standard interior cars. I have a box of mismatched retractors and not many with dates. Thanks
25
General Discussion / GM master parts books
« on: June 23, 2009, 06:11:07 PM »
I went by a local GM dealership today that is closing and was able to buy the 1967-1976 camaro master parts book along with the 1971-76 Vega parts book. I paid 20 dollars for the pair of them. Try out the dealerships that are closing in your area if you would like a set.
26
Restoration / Wiper arm colour
« on: June 01, 2009, 01:42:32 PM »
What colour are the wiper control arms inside the wiper cowling suppose to be? Thanks
27
Originality / Tail pipe adapter plate
« on: April 21, 2009, 12:57:43 PM »
Did 1968 cars with duel exhaust have the adapter plate on the rear frame rail like te 69 cars do?
28
General Discussion / Rod bolts
« on: April 16, 2009, 02:02:20 AM »
What size were the rod bolts used on first generation camaro motors? Thanks
29
Restoration / Ricks pistons
« on: April 08, 2009, 11:31:56 PM »
Does anyone know if Rcks First Generation piston include the rings with the 302 pistons ?
30
Restoration / honing a engine cylinder
« on: April 07, 2009, 11:57:21 PM »
How much material is removed when honing a cylinder ? Can standard pistons be used after honing?