436
News:
Welcome to the CRG Discussion Forum!
Classified ads are not allowed on the forum.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
437
General Discussion / Re: 1967 camaro 4K convertibles
« on: November 08, 2022, 02:27:01 AM »
Cool Shot, esp the Light rays streaming above the trees. Tripod that shot and a little longer exposure you can make light do some fantastic things.
Cool fence too.
Cool fence too.
438
General Discussion / Re: 1969 Z/28 on Mecum
« on: November 08, 2022, 02:24:37 AM »
I think the Factory Rivet sealer usually Lacks a "Finger Print"! That is Not consistent with Factory samples Right Guys.\
LoL
LoL
439
General Discussion / Re: 1968 1969 headlight actuator shields
« on: November 06, 2022, 04:01:18 AM »
1968 (LOS) 12E
440
Originality / Re: hood/headliner insulation question-1969 Z28
« on: November 01, 2022, 03:20:12 PM »
Is there a current replacement for this material Lloyd?
Thanks,
Jim
Thanks,
Jim
441
Restoration / Re: 1969 bucket seat hinge questions
« on: October 30, 2022, 05:28:24 PM »
My Guess would be Krylon Dull Alum # 1403
442
Research Topics & Reports / Re: Fuel Pump Research
« on: October 28, 2022, 03:07:44 AM »
Later Service unit BBC
443
Decoding/Numbers / Re: Big Block Fan Shroud
« on: October 27, 2022, 01:02:59 AM »
Close up of "Overstamped" Part Numbers & Mfr. Logo
Looks like they double stamped it with the superseded PN
Unit cleaned up real good with a light buffing with Meguires Plastic cleaner-polish.
Looks like they double stamped it with the superseded PN
Unit cleaned up real good with a light buffing with Meguires Plastic cleaner-polish.
445
Decoding/Numbers / Re: Big Block Fan Shroud
« on: October 26, 2022, 06:59:14 PM »
Found a 3945789 heat-stamped, in Great Shape. Perfect to replace my China wonkie Piece of work version.
446
Originality / Re: Hood Insulation Pad Interference
« on: October 23, 2022, 05:26:48 PM »
BDY-1224 & BDY-1225
Heartbeat City Camaro
Heartbeat City Camaro
447
Originality / Re: Hood Insulation Pad Interference
« on: October 22, 2022, 05:01:40 PM »
Unfortunately, That Entry Level Cheaper (Affordable) Generic under hood insulation is just that.
I believe there are two mfr. (versions) of the Molded flat hood insulation that have nicer features and better sizing. Which includes increase initial cost and shipping (Flat)
Then there is an opportunity to get the correct four hole plastic retainers also.
I believe there are two mfr. (versions) of the Molded flat hood insulation that have nicer features and better sizing. Which includes increase initial cost and shipping (Flat)
Then there is an opportunity to get the correct four hole plastic retainers also.
448
General Discussion / Re: 1968 special paint
« on: October 21, 2022, 06:53:35 PM »
Yes,Yes!
^^
I was just polishing a Set for my 68Z I am going to Add Z21 style trim to my Vinyl Top Car, (C2) even if it was not equipped new since I feel the same way about the appearance...
CHeers!
Jim
^^
I was just polishing a Set for my 68Z I am going to Add Z21 style trim to my Vinyl Top Car, (C2) even if it was not equipped new since I feel the same way about the appearance...
CHeers!
Jim
449
Decoding/Numbers / Re: Flywheel Number
« on: October 21, 2022, 06:24:09 PM »
Well, to my mind would be, the Motor might have been balanced with the Existing Flywheel and now you are introducing a different flywheel that was NOT balanced with the rotating assembly, is this wise or acceptable?
I am not sure
Just throwing it out there for discussion purposes.
Guys?
I am not sure
Just throwing it out there for discussion purposes.
Guys?
450
General Discussion / Re: 1969 Camaro Z/28
« on: October 18, 2022, 07:14:48 PM »
It could be a case of insufficient "reach" or length on the replacement rivets and they are cocked and barely gripping on the inner structure.
Funky for SURE!
Funky for SURE!