Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - john302

Pages: 1 ... 22 23 [24] 25
346
Originality / rocker panel rubber flaps
« on: March 21, 2008, 01:08:43 PM »
Does a 68 have the little rubber flaps on the rear inner rocker panel? All 69 models  I have seen have them,but never seen on a 68. Thanks John

347
Originality / Re: 1969 power brake master cylinder cap wording
« on: March 10, 2008, 10:39:20 PM »
anyone????

348
Originality / 1969 power brake master cylinder cap wording
« on: March 09, 2008, 02:27:36 AM »
Does anyone know when they changed the power brake master cylinder cap wording? The early caps have  USE DELCO BRAKE FLUID stamped in the cap ,and the later ones have USE DELCO SAEJ1703 BRAKE FLUID.  ??????????? around what month in 69 did they change????????

349
Originality / 1968 z/28 factory headers
« on: March 01, 2008, 04:20:39 AM »
Does anyone know how correct the repo 68z headers are? Is there more then one person making them? The only place I see them for sale is TA restorations in CA.  The persons name is Brent?   Anyone own a set ?  Thanks John

350
Originality / Re: 1968 z/28 water pump pulley reinforcement plate?
« on: February 20, 2008, 01:52:12 AM »
I was confused by the assembly manual also. Thanks for the quick replies .  John K.

351
Originality / 1968 z/28 water pump pulley reinforcement plate?
« on: February 17, 2008, 11:31:37 PM »
Does a 1968 z/28 use the reinforcement plate between the upper pulley and the water pump flange? most other v8s use these up to 1968 but not sure on the z?     Thanks John

352
General Discussion / Re: One pricey '68 Z/28...
« on: February 14, 2008, 02:27:13 AM »
    Very true William. 1968 z/28s are my favorite cars I would no interest in this car at all. I would much rather have an original untouched z with owner history and docs.

353
Originality / Re: correct plating on shock hardware
« on: February 13, 2008, 01:06:08 AM »
1968 z/28 front shocks and rear shocks    thanks

354
Originality / correct plating on shock hardware
« on: February 11, 2008, 02:07:02 AM »
What is the correct plating on the shock washers and the top nuts? is it silver zinc, grey phosphate?   

355
Originality / correct distrubutor cap 1968 z/28
« on: January 26, 2008, 12:40:30 AM »
What would be the correct 308 distrubutor cap for my December 1967 built 1968 z/28? Would it have  Delco Remy  patent pending  r   on the top of the cap? or without the r ? does anyone know this?  thanks John 

356
Originality / Re: Intake pipe plugs z/28 / l78
« on: January 23, 2008, 02:44:58 AM »
Jerry, yes the pipe plugs in the front of the intake. Thanks John

357
Originality / Intake pipe plugs z/28 / l78
« on: January 21, 2008, 05:30:36 AM »
What is the correct plating on the intake pipe plugs on a z and a l78? black phosphate, bare steel?     thanks John

358
General Discussion / Re: crager ss wheels help ????
« on: January 14, 2008, 02:38:30 AM »
what is the offset on yours? what thickness spacer? what size tires ? do they rub?  thanks john

359
General Discussion / crager ss wheels help ????
« on: January 13, 2008, 02:48:56 PM »
Does anyone know if the new crager ss wheels that you can purchase today are the same as the ones in the 60/70s?If they are different what has changed on them? also what size would look/fit the best on a 68z/28. 15 inch by 6 or 7inch with the stock Goodyear Wide treads.     Thanks John

360
Decoding/Numbers / Re: 67/68 z28 cowl plenum
« on: January 09, 2008, 01:31:18 PM »
THANKS FOR THE INFO.  JOHN

Pages: 1 ... 22 23 [24] 25
anything