316
Originality / CORRECT DISTRIBUTOR CAP
« on: November 24, 2008, 04:43:58 AM »
When did delco remy add the R on the patent pending on top of the cap? What is correct for a 12d 1968z. Thanks John
News:
Welcome to the CRG Discussion Forum!
Classified ads are not allowed on the forum.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
317
General Discussion / Re: Chicago Vettefest anyone going?
« on: November 21, 2008, 12:16:55 AM »
I will be there friday and saturday.Really wanted to bring the brown z again this year,but the weather is horrible up here. John
318
Originality / 67-69 upper and lower front control arms
« on: October 09, 2008, 12:57:50 AM »
What is the correct amount of gloss on the arms?I know they are alittle bit more glossy then the sub frame,but how much more? Would a 100 gloss be to much? thanks John 
319
Originality / Re: original small block spark plug heat shields
« on: September 21, 2008, 01:38:22 PM »
Thanks for the info Jerry.
320
Originality / Re: original small block spark plug heat shields
« on: September 21, 2008, 12:45:31 AM »
anyone ??
321
Originality / Re: 1968 z28 distributor
« on: September 18, 2008, 01:15:53 AM »
My fathom blue 12d 68z has the original 266 dated july 67.I believe a Feb car should have a 467. John
322
Originality / original small block spark plug heat shields
« on: September 17, 2008, 01:40:59 AM »
I am going to replate my original heat shields for my 68z,what is more correct silver zinc or silver cad.The repops are galvinized which I believe is incorrect.Siilver zinc might be alittle to bright. The nos ones that I have seen look silver cad plated?What is more durable cad or zinc? Thanks John
323
Originality / 67-69 camaro rear spring shackles
« on: September 08, 2008, 02:52:07 AM »
Are the rear spring shackles painted black or bare steel? All of the originals I have seen look bare. what is correct? Thanks John
324
Originality / 1968 z/28 timing tab
« on: August 25, 2008, 03:11:04 AM »
Hello , Does anyone know if the timing tab should be painted on a 68z.Getting ready to paint my engine and I want it to be correct. Thanks John
325
Originality / Re: groove machined in original rear brake shoes
« on: August 23, 2008, 02:17:37 AM »
Hello , thanks for the info. Do you want to sell a pair off nos shoes?I will step up!!!!!! Thanks John
326
Originality / groove machined in original rear brake shoes
« on: August 19, 2008, 02:03:05 AM »
I just looked at my original rear shoes from my 69z and the front shoe (rear brakes) has a groove machined in the lining.I think these are the true original shoes that the left the factory with. The groove is about a 1/2 wide. Thanks John Are these correct??
?
327
Restoration / Re: Wire harness clip
« on: July 07, 2008, 10:48:56 PM »
Nobody makes them,find a good used one on ebay.
328
Restoration / original freeze plugs
« on: July 02, 2008, 01:42:56 AM »
Does anyone know were to purchase a set of freeze plugs with no writing on them. All of the replacement ones have some kind of marking stamped on them.The originals have nothing stamped on them. Thanks John
330
General Discussion / Re: CAMARO NATIONALS AT CARLISLE
« on: June 27, 2008, 02:15:53 AM »
Had a great time at the show.Jerry is correct it is the best camaro show on the planet.The best camaros are there.I seen the best paint /body work ever on a camaro.The blue ss/rs 1968 camaro that East Coast painted/Lucas restored.Wow!!!!!!!!