CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
November 28, 2014, 04:37:51 PM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
106660 Posts in 12435 Topics by 4791 Members
Latest Member: DEL
* Home Help Search Login Register
  Show Posts
Pages: 1 [2] 3 4 ... 21
16  Camaro Research Group Discussion / Maintenance / Re: sway bar bushing replacement on: September 14, 2014, 04:05:08 AM
These are the bushins that are supposed to be correct for the bracket with the fingers.  I have gotten two sets from different vendors and they are exactly the same. I also picked up a set for the other bracket and it is very obvious they are incorrect
17  Camaro Research Group Discussion / Maintenance / Re: sway bar bushing replacement on: September 13, 2014, 03:37:02 PM
this is what i get
18  Camaro Research Group Discussion / Maintenance / sway bar bushing replacement on: September 12, 2014, 06:07:06 PM
I am in the midst of replacing my sway bar to frame bushings on my 69 , but no matter how I install them, it just doesn't look right
I have the later year mounts(with fingers).
any pointers? does the narrower slip under the top? is it supposed to just squish, leaving an oval for the bar to sit in? do I need to cut something?
Thank you for the help
19  Camaro Research Group Discussion / General Discussion / Re: Got a story of a car you "loved & lost" or sold? And found...years later? Share on: September 04, 2014, 09:04:48 PM
my camaro never quite got away - just haven't had her road worthy for 18 years
20  Camaro Research Group Discussion / Originality / Re: Paint on steering components on: August 26, 2014, 09:55:55 PM
http://www.camaros.org/forum/index.php?topic=3926.15

I saw this one that mentions the blue daub, but nothing about the yellow x by the A arm pocket
21  Camaro Research Group Discussion / Originality / Re: Paint on steering components on: August 26, 2014, 08:27:49 PM
and
22  Camaro Research Group Discussion / Originality / Re: Paint on steering components on: August 26, 2014, 08:23:47 PM
here are some pictures of what i found.  If the CRG thinks they are too detailed and might help over-restorers, please remove them
23  Camaro Research Group Discussion / Originality / Paint on steering components on: August 19, 2014, 07:41:24 PM
Has anyone noted any paint/ inspection daubs on the steering components?
While cleaning my subframe I found some additional markings  Grin
in addition to the original spring tags
24  Camaro Research Group Discussion / Restoration / AC Compressor on: August 16, 2014, 07:23:14 PM
Does anyone know of a place that will rehab an ac compressor?
25  Camaro Research Group Discussion / General Discussion / Re: valve confusion on: August 13, 2014, 07:13:34 PM
stopped by the machine shop yesterday and 202 valves fit the heads
26  Camaro Research Group Discussion / General Discussion / Re: valve confusion on: August 09, 2014, 09:59:57 PM
I got a call from my machine shop today letting me know the valves I had purchased to replace my originals were too small.

Valve head too small or valve stem too small?
valve head
I purchased direct replacement valves for the L48
27  Camaro Research Group Discussion / General Discussion / Re: valve confusion on: August 09, 2014, 11:14:44 AM
Colvin in CBTN shows the 041 was used (I assume in rare cases) as an alternative head on the Z's, and unverified as the Corvette 350/350 heads. I guess it might be possible that they could have been installed on a 350/300 by mistake (same 041 head with 1.94/1.50 valves). Depends on how long you have known the engine - possible upgrade at some point to the 2.02/1.60 valves ?

Aberrations are difficult to explain, even more difficult to verify.

Regards - 

one family vehicle
I understand that they could have used, though not very likely, a 041 head on a 302 or a 350/350 - but from what I know, those types of motors were all built at Flint. I am under the impression that Tonawanda did not build any of the 302 or 350/350 motors, thus would not have had a need to install the larger valves
28  Camaro Research Group Discussion / General Discussion / valve confusion on: August 09, 2014, 02:03:50 AM
I got a call from my machine shop today letting me know the valves I had purchased to replace my originals were too small.
I have a 350/300 with 041 heads and purchased the 1.94 and 1.50 valves
Are these not the correct valves? What other valves would be in 041 heads?
This was a Tonawanda built motor so it should not have 2.02/1.60. am I right with this thinking?
I know the history of the car and know the heads have only been off twice, once to repair a head gasket and when I replaced the rings.
29  Camaro Research Group Discussion / General Discussion / Re: Do You Still Have Your First Car? on: August 06, 2014, 08:17:21 PM
yes i do...
but it is in pieces Cry
69 Camaro!!
I got it cheap - ish
I had to rebuild the motor and pay all the registration fines ammounting to a little over $2500. I drove it until it wouldn't pass smog, would you know the following year the cut off date was moved to '74
30  Camaro Research Group Discussion / General Discussion / Re: Mecum Anahiem on: November 22, 2013, 07:46:39 PM
Yesterday the Shelby van was a head turner, as was the orange/white stripe 69 Camaro.

The Shelby van? You mean this turd? We stopped to look at it only because we couldn't figure out why it was there.

Is it a desirable vehicle? We kind of thought it represented a low point in an otherwise great mans life.





Yep that one - It was a WTF on the tow truck
Pages: 1 [2] 3 4 ... 21
Powered by MySQL Powered by PHP Powered by SMF 1.1.20 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.093 seconds with 18 queries.