Messages

961

Originality / Re: What is this connector for???

« on: May 19, 2007, 02:27:07 PM »

there you go ron. thats a better pic than what i sent you. mine was taken while it was still in the car so i would remember how it went. the second clip goes in one of the bellhousing bolt holes.
buddy

962

Decoding/Numbers / Re: Z10 trim plate

« on: May 19, 2007, 01:49:05 AM »

looks good to me

963

Decoding/Numbers / Re: YH wheel dates correct for my Z?

« on: May 13, 2007, 08:22:12 PM »

jerry. i just checked out the pics of the yh wheels on your survivor car. same date as mine. the vin is 3,000 after mine. the date on my m-21 is actually four days after the survivor. they must have been stacked up. beautiful car. see you at the nats. 67 wont be ready. will cruise down in the 99 ss.
buddy

964

Decoding/Numbers / Re: YH wheel dates correct for my Z?

« on: May 12, 2007, 06:52:47 PM »

my car is an 05A car and my wheels are dated 4-21. i would say there has to be some lag time in there. i could use two more as two were damaged. wheree are they and how much?
thanks
buddy

965

Restoration / Re: Best way to restore finish, aluminum intake & transmission

« on: May 06, 2007, 07:02:23 PM »

johnz. what is the sticker on the inner wheel well by the heater hose?

966

Originality / Re: What is this connector for???

« on: May 06, 2007, 06:59:14 PM »

ron. the hole next to the wiper motor is the hole for the oil pressure line. my 67 rs/ss doesnt have a rubber grommet. the fitting is held in with a nut on the engine side.

967

Originality / Re: What is this connector for???

« on: May 06, 2007, 06:55:34 PM »

johnz, that is a 67 firewall.

968

Originality / Re: 67 CAMARO SUBFRAME

« on: May 01, 2007, 02:05:33 PM »

my 67 rs/ss is a 12D production norwood car and has the old style subframe w/o the holes. i'll have to get my six year old to post a picture for me.

969

1968 - Orphans / Re: 8N360448 - I have your warranty book

« on: April 17, 2007, 02:28:12 AM »

better yet, send us pictures of spring break!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

970

Decoding/Numbers / Re: Need help on this engine code

« on: April 11, 2007, 09:05:39 PM »

i cant see the beginning of that number, but alot of times, a bebuilder will stamp numbers onto a block so they can keep track of when it was rebuilt and what was done to it.

971

General Discussion / Re: Subframe to body, alignment

« on: April 10, 2007, 02:37:48 AM »

find a threaded bolt that fits the alignment hole. tighten  a nut attaching it to the chassis.install the chassis and torque it down. remove the alignment bolts.

972

General Discussion / Re: hero member

« on: April 01, 2007, 09:18:07 PM »

boy do i have a loooooooong way to go!!!!!!!

973

General Discussion / Re: How Much Do You Drive?

« on: April 01, 2007, 09:16:36 PM »

not enough!!!!!!!!!!

974

Decoding/Numbers / Re: Muncie vin #'s

« on: March 25, 2007, 04:07:59 AM »

67 doesnt have the 1 in front of it. 68 and 69 do.

975

Restoration / Re: 1100814 Alt and 9078 Brake booster.

« on: March 19, 2007, 03:21:05 AM »

www.z28camaro.com