CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
August 02, 2014, 01:34:46 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
102558 Posts in 12096 Topics by 4669 Members
Latest Member: paulmanta
* Home Help Search Login Register
  Show Posts
Pages: [1]
1  Camaro Research Group Discussion / Decoding/Numbers / Re: Looking for info on 124379n579679 on: December 20, 2011, 01:28:45 AM
Joe,

My brother owned that car back in the 90's. That vin sequence is unique and I thought I recognized it. The gentleman building it passed away and my brother purchased it from the family. It was a burnt orange color and it had a roll bar, coil overs, and ladder bars but factory wheel wells. The rear should still show remnants of the steel brackets for the coil overs and ladder bars as we put leafs back under it. My knowledge of camaros back then wasn't as detailed as it is now but from what I remember the car had signs of being an original z28 but it was missing the trim tag. The motor wasn't original. I can't say about the trans and 12 bolt. I thought it had remnants of dusk blue in the crevices. He ended up selling the car a few months later.
2  Camaro Research Group Discussion / General Discussion / Re: Holley 4346 question on: October 12, 2011, 01:03:44 PM
Thanks guys. I phoned Holley tech and was told that the 4346 does not have the check ball.
3  Camaro Research Group Discussion / General Discussion / Re: Holley 4346 question on: October 10, 2011, 07:13:37 PM
Hi Marty,
The Holley rebuilding book that I'm referencing states that most have the check ball but some have a metered restriction orifice. However it doesn't reference which list numbers should have it. Mine didn't have the check ball but before I reassemble it I want to be sure.
4  Camaro Research Group Discussion / General Discussion / Holley 4346 question on: October 10, 2011, 04:00:18 PM
Can anyone tell me if the 4346 780 should have a check ball in the vacuum secondary housing?
5  Camaro Research Group Discussion / Decoding/Numbers / Re: Correct date range on: February 22, 2011, 02:52:25 PM
Steve,

My 04C L78 pacer's 837 is 9D3.
6  Camaro Research Group Discussion / General Discussion / Re: FISHER BODY MEASUREMENT on: February 18, 2011, 02:22:18 PM
Dave,
For whatever it is worth, I took several measurements. The rear springs and tank are out of my 69 pace car. Measuring inboard edge to inboard edge, using a stanley fatmax tape measure with bushings and a bolt in place to get the centerline, I came up with 42 1/2". Went right to left, left to right, several times to eliminate any possible error on my part. I also did this on my 69 x22 coupe drag car, which still has factory rails, but has coil overs and a fuel cell in the trunk. I came up with 42 9/16". Both cars have the original rails. Hope this helps.

Chris
7  Camaro Research Group Discussion / Research Topics & Reports / Re: 69 decklid emblem holes on: April 17, 2008, 11:05:02 PM
Kurt,
My brown scuncio car has two sets of holes. I think you have the data on it. 05E X11D80
Pages: [1]
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.084 seconds with 19 queries.