CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
July 28, 2014, 07:28:53 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
102436 Posts in 12088 Topics by 4667 Members
Latest Member: hrascoll
* Home Help Search Login Register
  Show Posts
Pages: [1]
1  Camaro Research Group Discussion / Restoration / Frt. Tire size on: November 13, 2006, 08:16:41 PM
Any of you that are running larger than stock tires please advise me as to size and what problems you have ... rub etc. This would be a great help! Thanks, Bruce   
2  Camaro Research Group Discussion / Restoration / 67 speed warning help needed on: July 26, 2006, 02:08:28 AM
Hi All, Redoing my 67 dash and making an upgrade to speed warning speedo. The shop book shows very little on this, and I need help !!! Where does the wire go to power this? The shop book show a stud of some sort on the top side of the housing Huh?? The wire dia. shows this going to the lighter Huh? Any help would be welcome. Also looking for a sorce for the buzzer and bracket. Thanks, Bruce   
3  Camaro Research Group Discussion / Restoration / 67 frt. tire size on: May 25, 2006, 08:13:11 PM
What is the largest tire size the will fit on a 67? Non rubbing only please. Thanks
4  Camaro Research Group Discussion / Restoration / 67 speedo cable routing / clips on: May 25, 2006, 07:14:04 PM
Could someone point me to a better drawing or picture then the assm. book on the speedo clip/s location and cable routing for a 67 396 / 4spd conv. Any help much needed!!!! Thanks, Bruce 
5  Camaro Research Group Discussion / Restoration / 67 speedo cable / 4 spd cars on: May 21, 2006, 07:19:45 PM
Hello All, went to install the speedo cable last night and found a drawing in the assm. book that shows a right angle drive at the transmission on 4 spd cars and completly different routing of the cable. This was a basket case that I did not take apart and of course I can find no such part in all my baskets ! Nor can I find such a part listed in the books from Ricks and the likes. Did the 4 spd cars have these Huh?? If so, where does one find them Huh  Thanks. Bruce in MD
6  Camaro Research Group Discussion / Restoration / Re: Bleeding Brakes on: April 14, 2006, 03:51:46 PM
Hi Gang, Yes I did bleed the master off car, and yes I found your posting but my problem is not air coming out the bleeders, I get just a nice flow of fluid. I keep bleeding & bleeding, no air. I wonder if it is somehow trapped in the calipers Huh? Thanks for the input. Bruce   
7  Camaro Research Group Discussion / Restoration / Bleeding Brakes on: April 12, 2006, 07:07:24 PM
Hi all, Have a 67 with all new parts in the brake system, new lines, booster, wheel and master cyl, calipers, shoes, pads, proportioning valve, etc. Went to bleed it and just cannot seem to get all the air out .... brakes pump up and I get a nice flow from all 4 bleeders, but still have no petal. have bleed it 10 times, still no air coming out but no petal with out pumping. Have noticed that the bleeders in the calipers seem to be much lower than the top of the piston bore .... can air be trapped in that area and if so, how do I get it out? Thanks!! Bruce 
8  Camaro Research Group Discussion / Restoration / Re: To Dye or Lacquer? on: March 18, 2006, 08:39:32 PM
Many years ago I repainted a dash pad and all the hard panels in my Elcamino, the painter at the dealer where I worked set me up with a "flex" agent to mix in with the lacquer. Worked like a charm. Was off the shelf dupont. Good luck, let us know how it goes. Bruce 
9  Camaro Research Group Discussion / Mild Modifications / Exhaust system for 67 ???? on: March 06, 2006, 09:09:05 PM
I have a 67 conv. with a 396 / 4 spd and hooker str. back headers which now needs the rest of the exhaust. I have been looking at the kits from summit, magnaflow, flowmaster and even got a few prices from local shops for a custom exhaust. So, what things do I need to look for? Does a 67 need to have the transverse muffler or will 2 smaller mufflers really fit under the car? Other issues? Thanks, Bruce
10  Camaro Research Group Discussion / Mild Modifications / 67 Exhaust header back on: January 27, 2006, 09:47:37 PM
Hey !!! I have a 67 Conv. BB 4 spd with str. back hooker headers. I need the rest of the exhaust but keep finding the after market kits listed as "all except conv." Yet the local dealer reports part numbers are the same for conv. or hardtop. Has any one done a conv. Huh Thanks.
11  Camaro Research Group Discussion / Restoration / 67 console wiring info on: December 29, 2005, 08:35:45 PM
Where can I find the wiring diagram for a 67 console gauge pack? Thanks, Bruce
12  Camaro Research Group Discussion / Originality / 67 console gauges on: December 10, 2005, 07:28:32 PM
Just got my new OER gauge pack and it looks great, I also found a "orig console with the gauge pod and parts of the gauges" at carlisle this last fall plus I have the orig. pod from the car with date sticker still intact. Question is ... the orig pod has chrome trim around the gauges, the other 2 do not. Was this area left black to I D the repro? Or did some one remove the paint on the orig. pod somewhere along the way Huh? Thanks, Bruce     
13  Camaro Research Group Discussion / Restoration / Re: Trunk Spatter Paint Color for 1st Gens. on: December 09, 2005, 10:43:42 PM
Any info on how high towards the deck lid the spatter went ?  Thanks, Bruce   
14  Camaro Research Group Discussion / Restoration / 67 exhaust ?? conv stiffner on: December 09, 2005, 10:35:32 PM
Hi, Can anyone tell me why the aftermarket groups all list header back exhaust kits for 67 hardtops EXCEPT convertibles ?? I understand my conv. has a stiffing plate, but was the factory big block exhaust not the same? Thanks, Bruce   
Pages: [1]
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.087 seconds with 19 queries.