CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
September 16, 2014, 08:31:19 PM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
104462 Posts in 12231 Topics by 4716 Members
Latest Member: Hgtech
* Home Help Search Login Register
  Show Posts
Pages: 1 2 [3]
31  Camaro Research Group Discussion / General Discussion / Re: CRG t-shirts - How to order on: June 20, 2013, 08:23:07 PM
Count me in!  Grin

Eric
Rocky Mount, Va
Sizes 1 XL, 1 XXl for 2 shirts total
Print on front and back of both
32  Camaro Research Group Discussion / Decoding/Numbers / Re: 1968 Z/28 block code "MI" COPO 9665 info. on: January 09, 2006, 10:13:28 AM
I ran across the information in the Camaro White Book by Mike Antonick. It was in the 1968 block suffix section. I to had never heard of A COPO 9665 until I saw this or have I seen an "MI" coded 302 block. Appreciate the input. Maybe someone here has some more information.
33  Camaro Research Group Discussion / Decoding/Numbers / 1968 Z/28 block code "MI" COPO 9665 info. on: January 06, 2006, 06:51:30 PM
I like to consider myself pretty knowledgable on 1st gen camaros, but I ran across something today that I was hoping someone may be able to help shed some light on for me. I've always been under the impression that the only 1968 Z/28 block code was "MO", but today I ran across a piece of information stating that a block code of "MI" was used when COPO 9665 was specified. Anyone out there got any information on this and if it is correct? I've never heard of the "MI" block code for a 68 Z/28 and was wondering if anyone could verify they exist. Also was wondering if chevrolet did indeed produce a COPO 9665 in 1968, what did the package consist of?  Another COPO for 1968 I would like some information on is 9737 anyone know what this option consisted of? Thanks in advance.
34  Camaro Research Group Discussion / Restoration / Re: new quater panels on: November 01, 2005, 11:56:37 AM
Replacing the rear quarters may seem very intimidating at first but once you "dig in " to the project it really isn't that bad, just time consuming. I've replaced both rear qtrs. on my '67 and my '69 along with many other pieces of sheet metal along the way. As far as tools go, it sounds you like you have a good base to start with but you should really consider a compressor as a purchase as it will prove invaluable to you. Also, you should invest in a spot weld cutter and quality 3/8" or 1/2" drill to drill out the spot welds. You are also going to need at least a hand held propane torch to melt out the old body solder where the sail meets the roof panel. If you don't intend on using a compressor and air cut-off tool, there are many electric cut-off tools out there and you will definately need one, a dremel tool will not hold up to cuting off a qtr. panel.
Another thing to take into account is what is the extent of the body rot on this vehicle? If the qtr. panel is rusted along the outer edge of the wheel opening, you may need to replace the outer wheel well. Not a difficult task but one you may want to keep in mind.
Other than that, I like to start by melting out the old body solder and taking it from there. The hardest areas to remove I find are where the qtr. joins the drip rail. Very hard spot welds to get at with anything but a cut-off tool and it takes a delicate touch not to cut through the bottom of the drip rail. Other than that most of the spot welds are fairly easy to get to. It is also alot easier if cut out the face of the qtr. so all the welds are easier to get at. 
Pages: 1 2 [3]
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.322 seconds with 18 queries.