CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
April 26, 2015, 10:45:47 AM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
112298 Posts in 12901 Topics by 4938 Members
Latest Member: chevyglassguy
* Home Help Search Login Register
  Show Posts
Pages: 1 ... 73 74 [75] 76
1111  Camaro Research Group Discussion / Restoration / Re: 1968 Camaro Front Coil Spring Replacement on: August 02, 2006, 07:51:37 AM
NOT recommended, NOT safe, but I have in the past compressed coils off of the car, and strapped them using wire. Then inserted in the car, and cut the wire. Not always having the right stuff, we improvise.
1112  Camaro Research Group Discussion / General Discussion / Re: Rear Spoiler Mounting? on: August 02, 2006, 05:51:01 AM
I used a sheet of cardboard, over the studs, and trimmed to the spoiler base. Then laid it out on the trunk and punched, then drilled the holes. Took a little time, but it worked well. I have been told there is some variation (minor) in studs on the spoiler.

Tom
1113  Camaro Research Group Discussion / Mild Modifications / Re: front brake conversion to disc on: August 01, 2006, 07:31:51 PM
http://www.pozziracing.com/
1114  Camaro Research Group Discussion / Originality / Re: Power steer pump cap on: May 30, 2006, 01:52:33 PM
My 69 307 has the plastic cap - presumed original not a lot has been done to the car over the years.

Tom
1115  Camaro Research Group Discussion / Mild Modifications / fuel inject my 307 ? on: March 28, 2006, 09:33:11 AM
I have a plain 307 pg, with the original 2 bbl setup. I am looking to improve performance without overspending, and with as the original engine. Have any of you converted your small block to modern fuel injection? I am considering a junkyard system, so my questions are: What would be the best system for my 307? Which components do I need from the donor car? What additional components will be needed?

Thanks in advance,


Tom
1116  Camaro Research Group Discussion / Mild Modifications / Re: brake swap questions on: March 01, 2006, 04:16:53 PM
Rod,

Check the info on this site:
                                 http://www.pozziracing.com/
There is a lot of info on brake swaps, and other 1st gen topics

Good luck,

Tom
1117  Camaro Research Group Discussion / General Discussion / Re: Rear Seat Removal on: February 22, 2006, 09:59:05 AM
Thanks John,

I don't expect much, but might as well take a look.
1118  Camaro Research Group Discussion / General Discussion / Re: Rear Seat Removal on: February 21, 2006, 03:45:23 PM
John,

Any tricks involved? I have popped one side loose, but just put my foot through the floor trying to pop the passenger side. Would the build sheet be in any specific area, or "somewhere" on the bottom of the seat? I can pull the drivers side up part way, and don't see anything there. I would love to know what I have.

Thanks!

Tom
1119  Camaro Research Group Discussion / Mild Modifications / Re: Possible Axle swap on: February 04, 2006, 10:15:38 AM
Thanks John!
1120  Camaro Research Group Discussion / Mild Modifications / Re: Possible Axle swap on: February 03, 2006, 06:56:12 AM
John,

Thank you for the assistance. In your opinion, could the 3.90 be acceptable for an occasional use crusier if it had an overdrive tranny like the 700r4 or the 2004r? As best as I can tell there is nothing special about my Camaro, and I do not forsee a perfect restoration in the future.

Might be a dumb idea, but the price is right, and I would like a posi.

Thanks again,

Tom
1121  Camaro Research Group Discussion / Mild Modifications / Re: Possible Axle swap on: February 02, 2006, 06:28:15 AM
Don't need or want a 411, but I would like a posi. Just picked up a newer 350 truck block to build, and might stroke it. I am going to swap the glide for an overdrive, just not sure which one yet. I was hoping the 411 carrier could accept a milder set of gears. Reason I ask is It's been offered as trade for a junk benz I need to dump.

I'm more interested in the fold down seat than the 411.

Thank for the help,

Tom
1122  Camaro Research Group Discussion / Mild Modifications / Possible Axle swap on: January 26, 2006, 11:31:10 AM
I have been told of an available original 411 posi 12 bolt for my car. What should I be looking for if/when I get to check it out. I'm not thrilled with the thought of 411's at least not with today's gas prices. If I get the rear what ratios can be swapped. Mine is a 69 base 307 PG with I believe the economy geared rear.

Same person also may have a fold down rear seat, besides the seat itself, what else is needed to convert to the fold down?

Thanks,

Tom
1123  Camaro Research Group Discussion / General Discussion / Re: 69 Camaro How many left. on: January 08, 2006, 07:08:50 PM
sounds like a project for somebody. Document the most obvious diffs between the originals and the re-pops. There must be loads........
1124  Camaro Research Group Discussion / Decoding/Numbers / Re: Early vin # on: January 01, 2006, 09:39:10 PM
Have to disagree about Honda junk, my 91 Accord is still running strong at about 220,000 miles(oversize tires underdriving odometer by about 10% and 200,000 on the odo). Maintenance has been extremely rare. 3rd set of brakes, 3rd set of tires, lots of lof's not a lot more than that.

Tom
1125  Camaro Research Group Discussion / Mild Modifications / Re: 69 Z/28 Front disc brake upgrade on: November 16, 2005, 07:45:32 PM
Dave Pozzi (old forum) had a whole web page of info re brake swaps with other GM brake systems of the same era. Not the brand new high tech stuff, but still a whole lot better than drums. Not sure its still there, but its worth a google.

Good luck

Tom A
Pages: 1 ... 73 74 [75] 76
Powered by MySQL Powered by PHP Powered by SMF 1.1.20 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.08 seconds with 18 queries.