CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
July 30, 2014, 04:27:17 PM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
102494 Posts in 12091 Topics by 4669 Members
Latest Member: paulmanta
* Home Help Search Login Register
  Show Posts
Pages: 1 ... 72 73 [74] 75
1096  Camaro Research Group Discussion / Decoding/Numbers / Re: trim rings for rally wheels on: September 01, 2006, 05:10:31 PM
John,

Thank you! I figured someone here would be able to id these wheels.At least now I can look up and identify trim rings that will fit.

Tom
1097  Camaro Research Group Discussion / Decoding/Numbers / trim rings for rally wheels on: August 31, 2006, 11:19:53 AM
My PJ 69 307 glide came to me with a set of 15" rally wheels with center caps but no trim rings. I know these are not original, but I like them. Can anyone tell me what trim rings I need? I checked two of the rims, the other two need rust cleanup. I hoping to find a set of rings at the fall Englishtown swap. Any help appreciated.
The numbers around the valve stems are:

K 1 8   5 valve 1 2 FW
and
K 1 7  8 valve 1 7 FW

Thanks
Tom
1098  Camaro Research Group Discussion / Decoding/Numbers / Re: Please Decode on: August 10, 2006, 08:03:16 AM
Rich,

Thanks! VIN: 124379N601591

Everything matches with the car except the Vinyl top. I personally know the last two owners, and have no recollection of that, but will ask them.  I was already pretty sure, but just looking for confirmation. It's just a base 307 glide. As far as I know drive train should be mostly original, I understand there was a head exchange two owners back, and a new crank by the last owner. I;m not sure where this is headed yet. Never was a fan of vinyl tops. I'm really just looking for a fun driver.

Thanks again

Tom
1099  Camaro Research Group Discussion / Decoding/Numbers / Please Decode on: August 09, 2006, 07:03:13 PM
I think Trim Tag photo is attached. Nothing special, just want to verify what I have.

Thanks!
1100  Camaro Research Group Discussion / General Discussion / Re: 1987 IROC-Z on: August 04, 2006, 08:25:47 AM
I Havent used them yet, but I hear the folks at http://www.tpis.com/ are good.
1101  Camaro Research Group Discussion / Restoration / Re: 1968 Camaro Front Coil Spring Replacement on: August 02, 2006, 07:51:37 AM
NOT recommended, NOT safe, but I have in the past compressed coils off of the car, and strapped them using wire. Then inserted in the car, and cut the wire. Not always having the right stuff, we improvise.
1102  Camaro Research Group Discussion / General Discussion / Re: Rear Spoiler Mounting? on: August 02, 2006, 05:51:01 AM
I used a sheet of cardboard, over the studs, and trimmed to the spoiler base. Then laid it out on the trunk and punched, then drilled the holes. Took a little time, but it worked well. I have been told there is some variation (minor) in studs on the spoiler.

Tom
1103  Camaro Research Group Discussion / Mild Modifications / Re: front brake conversion to disc on: August 01, 2006, 07:31:51 PM
http://www.pozziracing.com/
1104  Camaro Research Group Discussion / Originality / Re: Power steer pump cap on: May 30, 2006, 01:52:33 PM
My 69 307 has the plastic cap - presumed original not a lot has been done to the car over the years.

Tom
1105  Camaro Research Group Discussion / Mild Modifications / fuel inject my 307 ? on: March 28, 2006, 09:33:11 AM
I have a plain 307 pg, with the original 2 bbl setup. I am looking to improve performance without overspending, and with as the original engine. Have any of you converted your small block to modern fuel injection? I am considering a junkyard system, so my questions are: What would be the best system for my 307? Which components do I need from the donor car? What additional components will be needed?

Thanks in advance,


Tom
1106  Camaro Research Group Discussion / Mild Modifications / Re: brake swap questions on: March 01, 2006, 04:16:53 PM
Rod,

Check the info on this site:
                                 http://www.pozziracing.com/
There is a lot of info on brake swaps, and other 1st gen topics

Good luck,

Tom
1107  Camaro Research Group Discussion / General Discussion / Re: Rear Seat Removal on: February 22, 2006, 09:59:05 AM
Thanks John,

I don't expect much, but might as well take a look.
1108  Camaro Research Group Discussion / General Discussion / Re: Rear Seat Removal on: February 21, 2006, 03:45:23 PM
John,

Any tricks involved? I have popped one side loose, but just put my foot through the floor trying to pop the passenger side. Would the build sheet be in any specific area, or "somewhere" on the bottom of the seat? I can pull the drivers side up part way, and don't see anything there. I would love to know what I have.

Thanks!

Tom
1109  Camaro Research Group Discussion / Mild Modifications / Re: Possible Axle swap on: February 04, 2006, 10:15:38 AM
Thanks John!
1110  Camaro Research Group Discussion / Mild Modifications / Re: Possible Axle swap on: February 03, 2006, 06:56:12 AM
John,

Thank you for the assistance. In your opinion, could the 3.90 be acceptable for an occasional use crusier if it had an overdrive tranny like the 700r4 or the 2004r? As best as I can tell there is nothing special about my Camaro, and I do not forsee a perfect restoration in the future.

Might be a dumb idea, but the price is right, and I would like a posi.

Thanks again,

Tom
Pages: 1 ... 72 73 [74] 75
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.093 seconds with 18 queries.