CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
April 20, 2014, 09:04:31 PM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
97291 Posts in 11694 Topics by 4578 Members
Latest Member: ronhill
* Home Help Search Login Register
  Show Posts
Pages: 1 ... 71 72 [73] 74 75
1081  Camaro Research Group Discussion / General Discussion / Re: Vinyl or Not? on: November 06, 2006, 12:50:18 PM
Now that I know my 69 had a vinyl top I'm thinking about replacing it. Can someone point me to a good starting point? I presume I will need all trim, fasteners, material, some type of template or measurements to start drilling etc.

Thanks,

Tom
1082  Camaro Research Group Discussion / Mild Modifications / Re: ECI Disc brake conversion on: October 23, 2006, 12:04:49 PM
You might want to check this site: http://www.pozziracing.com/brakes.htm#Converting_Drums_to_Discs

Seems very complete, and probably less expensive. Good Luck either way.

Tom
1083  Camaro Research Group Discussion / Decoding/Numbers / Re: HELP ON DECODIG COWL TAG on: October 10, 2006, 08:10:43 AM
Jason,

Click on the Decoding link in the table at the top of this page. Download and run the decoder. It worked well for me.

Good luck,
Tom
1084  Camaro Research Group Discussion / General Discussion / Re: What size wheels can I go with on a 69 Camaro? on: October 10, 2006, 07:57:20 AM
Steve,

I know this is not much help, but in the past when fitting tires, I have gone under the car and started from the current wheels and tires, then turned the fronts rack to rack, and measured clearances at each stop. Its a pain in the rump, but so far it has worked I have been able to predict the max tire for the existing rim. Changing rims would take additional calculations that I'm probably not ready for right now. Sorry I haven't done tires yet on my Camaro. Check the magazines, I have seen a couple of articles on what size tire can fit a 69 Camaro over the years.

Good luck,

Tom
1085  Camaro Research Group Discussion / Restoration / retrofitting fold down rear seat on: October 03, 2006, 12:48:37 PM
I bought a fold down rear seat back recently, I am ordering all the hardware to install it. Can anyone provide photos of the installed hardware so I have a reference when I try to set this up? Also I would appreciate knowing if pictures are of an original fold down, or a later modification.

Thanks!

Tom
1086  Camaro Research Group Discussion / Mild Modifications / fold down back seat on: September 23, 2006, 09:56:04 PM
Today I picked up a fold down seat back for my 69. It has some (very little) hardware with it. I presume I need the Fisher body manual for pictures. Don't have one yet, does any one have good photos showing the installation for the seat?

Thanks!

Tom
1087  Camaro Research Group Discussion / Decoding/Numbers / Re: trim rings for rally wheels on: September 01, 2006, 05:10:31 PM
John,

Thank you! I figured someone here would be able to id these wheels.At least now I can look up and identify trim rings that will fit.

Tom
1088  Camaro Research Group Discussion / Decoding/Numbers / trim rings for rally wheels on: August 31, 2006, 11:19:53 AM
My PJ 69 307 glide came to me with a set of 15" rally wheels with center caps but no trim rings. I know these are not original, but I like them. Can anyone tell me what trim rings I need? I checked two of the rims, the other two need rust cleanup. I hoping to find a set of rings at the fall Englishtown swap. Any help appreciated.
The numbers around the valve stems are:

K 1 8   5 valve 1 2 FW
and
K 1 7  8 valve 1 7 FW

Thanks
Tom
1089  Camaro Research Group Discussion / Decoding/Numbers / Re: Please Decode on: August 10, 2006, 08:03:16 AM
Rich,

Thanks! VIN: 124379N601591

Everything matches with the car except the Vinyl top. I personally know the last two owners, and have no recollection of that, but will ask them.  I was already pretty sure, but just looking for confirmation. It's just a base 307 glide. As far as I know drive train should be mostly original, I understand there was a head exchange two owners back, and a new crank by the last owner. I;m not sure where this is headed yet. Never was a fan of vinyl tops. I'm really just looking for a fun driver.

Thanks again

Tom
1090  Camaro Research Group Discussion / Decoding/Numbers / Please Decode on: August 09, 2006, 07:03:13 PM
I think Trim Tag photo is attached. Nothing special, just want to verify what I have.

Thanks!
1091  Camaro Research Group Discussion / General Discussion / Re: 1987 IROC-Z on: August 04, 2006, 08:25:47 AM
I Havent used them yet, but I hear the folks at http://www.tpis.com/ are good.
1092  Camaro Research Group Discussion / Restoration / Re: 1968 Camaro Front Coil Spring Replacement on: August 02, 2006, 07:51:37 AM
NOT recommended, NOT safe, but I have in the past compressed coils off of the car, and strapped them using wire. Then inserted in the car, and cut the wire. Not always having the right stuff, we improvise.
1093  Camaro Research Group Discussion / General Discussion / Re: Rear Spoiler Mounting? on: August 02, 2006, 05:51:01 AM
I used a sheet of cardboard, over the studs, and trimmed to the spoiler base. Then laid it out on the trunk and punched, then drilled the holes. Took a little time, but it worked well. I have been told there is some variation (minor) in studs on the spoiler.

Tom
1094  Camaro Research Group Discussion / Mild Modifications / Re: front brake conversion to disc on: August 01, 2006, 07:31:51 PM
http://www.pozziracing.com/
1095  Camaro Research Group Discussion / Originality / Re: Power steer pump cap on: May 30, 2006, 01:52:33 PM
My 69 307 has the plastic cap - presumed original not a lot has been done to the car over the years.

Tom
Pages: 1 ... 71 72 [73] 74 75
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.083 seconds with 18 queries.