Messages

16

Maintenance / Re: 68 Tilt column loose & turn signal switch removal

« on: October 29, 2021, 03:09:13 PM »

There are four critical tools to use in disassembly and reassembly - look at your Service Manual for the numbers of the pivot pin tool, special socket and the bowl (reassembly) driver, which keeps you from bending or crushing the collar when you drive it back in place after replacing the switch. I wish you luck in finding that one - that REALLY took a good while to locate.

Regards,
Steve

The pivot pin remover tool (J-21854) is available but I see where people have improvised here with other tools.

I have found several bowl drivers (J-21853).

 J-22599 is available also if that is the socket your referring to.

17

Maintenance / Re: 68 Tilt column loose & turn signal switch removal

« on: October 28, 2021, 05:08:25 AM »

I was aware of the pivot pin tool but not the special socket and bowl driver. Can you provide more info on that; pics; part #'s?

18

Maintenance / Re: 68 Tilt column loose & turn signal switch removal

« on: October 27, 2021, 05:20:39 AM »

I have a 67 tilt column and I want to replace turn signal switch and thinking about going thru the whole thing while I am at it.
 Paid $100 for the tool and feel lucky to have found one in good condition.

19

Maintenance / Re: 68 Tilt column loose & turn signal switch removal

« on: October 25, 2021, 07:00:55 PM »

There are 2 different PN's associated with the tool.
Here is pics of a tool I recently picked up.
Plus it will fit other car makes too.
https://theamcforum.com/forum/removing-turn-signal-switch-cover_topic67035_page1.html

20

Maintenance / Re: maintaining doors...

« on: September 29, 2021, 03:03:36 PM »

Door plugs recently acquired for reference.
Hard to believe they packaged these individually.

21

General Discussion / Re: Neat Video of my 68 Camaro and C10

« on: August 20, 2021, 05:55:50 PM »

Cool video! I like the Andy Gibb tune also.

22

Restoration / Re: GRILL RIVETS 1967 (or '68?)-

« on: July 22, 2021, 10:49:45 AM »

Thanks for the pics using that tool as I plan on doing the same with my RS grill and headlight door trim.

23

Originality / Re: Headlight Adjusting Screws & Nylon Nuts

« on: July 01, 2021, 10:16:30 PM »

67 adjusters screw length is 1 3/8" and so are the NOS #5953005 as listing in AIM in my pics in other thread posted above.
They are not black nor are the original ones I have.

I don't know about other years.

24

Originality / Re: Headlight Adjusting Screws & Nylon Nuts

« on: June 30, 2021, 04:50:05 AM »

I believe some are white also. At least that's is what's on my original 67 RS capsules.
The nuts are nylon and aftermarket are not in my experience.
http://www.camaros.org/forum/index.php?topic=17365.msg170811#msg170811

25

Restoration / Re: 1969 Hood Striker Assembly Finishes

« on: May 07, 2021, 10:58:49 PM »

While restoring some items that I planned in selling, I referenced this thread and hopefully came close to the intended result.

I noticed your spring has more coils than others. Is that a reproduction or just one you painted?

26

Garage Talk / Yenko.com site trouble?

« on: April 06, 2021, 02:49:32 PM »

What's up with the Yenko.com website?

27

General Discussion / Re: Headlamp adjuster screw

« on: October 26, 2020, 07:35:52 PM »

Ok I bought 6 and in order to make 2 sets found a couple more plus I this original set I purchased from Year One many years back when they designated NOS parts with a the letter N.
I may need a brain adjuster.

28

General Discussion / Re: Headlamp adjuster screw

« on: October 24, 2020, 06:53:43 PM »

Here is another one I have. Same nut slightly different screw. Nut has number 62 on bottom.

Hard to see the difference in picture. The screw head is actually not as thick as others.

29

Originality / Re: Does anybody know about this front convertible top bow "wedge"?

« on: October 23, 2020, 02:01:54 PM »

They look fairly accurate too although I don't have one compare side by side.
Here is a pic of an original. By the way if anybody has one in similar condition as the one in my pic PM me with price.

30

General Discussion / Re: Headlamp adjuster screw

« on: October 13, 2020, 11:09:15 PM »

Here is an update on these headlamp adjusters.

The 67 Camaro aim has this number 5953005 and looks to be same length screw as on a pair of RS capsules I own. However the nut is white. The nut has number 35 on it.

The other adjuster is a NOS bought from Year One many years ago. Same nut but (looks bigger in pic fore some reason) has number 60 on it.

The white nut on original capsule not pictured has number 11 on it.