CRG Discussion Forum
Welcome, Guest. Please login or register.
Did you miss your activation email?
October 22, 2014, 04:52:53 PM

Login with username, password and session length
Search:     Advanced search
Welcome to the CRG Discussion Forum!
Forum registration problems: Make sure you enter your email correctly and you check your spam box first. *Then* email KurtS2@gmail for help.
105646 Posts in 12336 Topics by 4753 Members
Latest Member: stpatrick
* Home Help Search Login Register
  Show Posts
Pages: 1 ... 5 6 [7] 8
91  Camaro Research Group Discussion / Originality / Re: Original console bolts (style) on: November 07, 2007, 06:36:01 PM
Are you talking about the two bolts that bolt the lower part of the console to the floor? I have a set of originals out of my car and I can take an image. I also have images of most of the other screws/bolts for a 68 console. Let me know a part number and I'll get an image.
92  Camaro Research Group Discussion / Originality / Re: Alt. pulley diameter? (L34/L35) on: September 13, 2007, 02:21:58 PM
The pulley isn't listed in the yearly charts because it's part of the alternator assembly and not called out for in the Assembly Manual so we don't have a part number.

If you look at the pulley chart sheet with all pulleys listed, there is a note at the end that says all 68 standard pulleys are stamped with a 7. I have several 1100794 alternators and all have this pulley. I also have a couple other 68 alternators with the same pulley.

Martin
93  Camaro Research Group Discussion / Decoding/Numbers / 9078 Booster Dates on: September 01, 2007, 02:16:38 PM
I have a January (01C) 68 LOS built car and I need some date code help. My car has power disc brakes but the booster and master cylinder were changed out over the years. I have picked up two boosters with 326 and 343 dates. Does anyone have a January LOS car with the original booster that can share the date?

Thanks.

Martin
94  Camaro Research Group Discussion / Restoration / Re: Getting Desperate on: August 22, 2007, 12:42:23 PM
The stabilizer mounting bracket in Paul's photo is correct for Muncie. The top curls toward the back of the trans when mounted. The Saginaw bracket curls toward the front of the trans when mounted. Hope this helps.

Martin
95  Camaro Research Group Discussion / Restoration / Re: Getting Desperate on: August 20, 2007, 08:20:37 PM
Measure the stabilizer rod from the hex nut that's part of the rod to the beginning of the mounting slot. If it's 6 7/8" it's for a Saginaw. If it's 6 1/16" it's for a Muncie SB.

Martin
96  Orphans - documentation or VIN-stamped drivetrains - in search of the original cars / 1969 - Orphans / 9N512221 Muncie M20 on: May 04, 2007, 10:17:02 AM
This Muncie was just on ebay. The car is out there, it was on ebay in 2002. Kurt made an attempt to contact the seller but had no response. So if you own this car or know about it, your M20 Muncie is out there.
97  Orphans - documentation or VIN-stamped drivetrains - in search of the original cars / 1968 - Orphans / 8N360803 - I have your engine on: April 02, 2007, 11:31:35 AM
I have this engine block, T1129MW. The story is the car was totaled with 30K miles early in life.
98  Orphans - documentation or VIN-stamped drivetrains - in search of the original cars / 1968 - Orphans / 8L312422 - I have your Muncie on: April 02, 2007, 11:28:54 AM
I have this Muncie transmission, date code P8R27.
99  Orphans - documentation or VIN-stamped drivetrains - in search of the original cars / 1968 - Orphans / 8N378525 - I have your Muncie on: April 02, 2007, 11:27:50 AM
I have this Muncie transmission, date code P8A15.
100  Site Comments / Discussion / Site Comments/Discussion / Re: Typo in crg reports - cooling on: February 21, 2007, 01:07:57 PM
Mine measures 1 9/32" for the body. It has the part number cast into it. Does yours?

Martin
101  Camaro Research Group Discussion / Restoration / Re: 3 groove crankshaft pully on: January 17, 2007, 07:25:20 PM
You will need 2 pulleys. There is either a single groove or double groove pulley attached to the balancer and a second single groove pulley for the power steering that bolts in front of the first pulley. There is a chart on the CRG website that lists the pulleys that you need. I believe the '66 crank pulleys are the same. You need to check the numbers and fit. AC crank pulleys are larger in diameter and need a smaller diameter water pump pulley so make sure you match up these pulleys.
102  Camaro Research Group Discussion / Decoding/Numbers / Re: 68 wheel rim date codes on: January 11, 2007, 01:33:31 PM
It's the only early date I've seen. I have seen other later 68 and 69 dates. There must be some dated earlier than November 67, I just haven't seen them.
103  Camaro Research Group Discussion / Decoding/Numbers / Re: 68 wheel rim date codes on: January 10, 2007, 01:49:01 PM
Yes, November 30, 1967. I'm collecting a set of these for my 01C car. That is the only XG date I've seen in 1967/early 68. I'm still looking for two! Is your car from Norwood?
104  Camaro Research Group Discussion / Decoding/Numbers / Re: 3919803 Intake (327/275 HP and 350/295 HP???) on: November 20, 2006, 03:11:19 PM
The date code J 7 7 is October 7, 1967. Martin
105  Camaro Research Group Discussion / Decoding/Numbers / Re: Bellhousing/flywheel/clutch for 67SS/RS350 on: September 08, 2006, 06:02:21 PM
The correct casting number for the flywheel is 3789733. I think the other number is the assembled part number.
Pages: 1 ... 5 6 [7] 8
Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2013, Simple Machines Valid XHTML 1.0! Valid CSS!
Page created in 0.098 seconds with 18 queries.