Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Marty

Pages: 1 [2] 3 4 ... 9
16
My car was delivered to George Olsen Chevrolet in San Francisco. Would be interested in a set of license plate frames. Martin

17
Originality / Re: '68 L35 1100794 Alternator
« on: April 18, 2014, 10:09:33 PM »
The pulleys and fans I've seen all have slots. I have 3 1100794 alternators and all 3 look like they have a thick flat washer. I don't see a split in it.

Martin

18
Restoration / Re: Disassembly of brake booster
« on: January 07, 2014, 04:26:32 AM »
The Chassis Overhaul Manual covers the overhaul of the brake booster and has diagrams of the parts. Martin

19
General Discussion / Re: 1969 396 valve cover ID
« on: April 21, 2013, 05:38:28 AM »
Maybe truck?

20
Originality / Re: Speedo cable Clips
« on: November 07, 2012, 03:50:58 AM »
I found some on Firebirds years ago but all mine were missing so I don't have extras. You might try some Pontiac parts vendors. Martin

21
Restoration / Re: 69 515 Voltage regulator R & R
« on: September 18, 2012, 12:42:02 AM »
I thought someone posted a thread about removing the guts from their VR and installing the guts from a solid state unit. Has the original base with p/n and date and the original lid. Martin

22
Originality / Re: Early 68' RS Grill Attaching Screws
« on: September 08, 2012, 11:56:49 AM »
I have a 68 but it's not an RS. I gathered lots of fasteners for my restoration.

Martin

23
Originality / Re: Early 68' RS Grill Attaching Screws
« on: September 07, 2012, 06:18:10 PM »
I looked closer at my screws and they were a different part number, 3419303! Sorry.

Martin

24
Originality / Re: Early 68' RS Grill Attaching Screws
« on: September 05, 2012, 01:19:55 AM »
The screw has a pointed tip so that would match the use of a u-nut.

25
Originality / Re: Early 68' RS Grill Attaching Screws
« on: September 04, 2012, 10:49:14 PM »
I have 2 original 9419303 screws. I'll try to take photos but I'm recovering from surgery so it might be a couple days. They're short hex head screw with an indented head. Probably 1/4" socket for the head but I'll check it out.

I'll look for the 9422836 nuts some more. I couldn't find any in my storage boxes.

Martin

26
Originality / Re: Ashtray bracket mounting screws
« on: July 24, 2012, 01:48:09 AM »
what is the part number?

27
General Discussion / Re: Distributor Weights and Springs
« on: March 09, 2012, 04:04:19 AM »
Used distributors at swap meets are $5-10. Maybe cheaper to do that for parts. Martin

28
General Discussion / Re: 1968 L-89 Convertible on ebay.
« on: February 22, 2012, 06:13:54 PM »
Wrong power steering pump pulley.
Wrong crank pulley for a power steering car.
Smog missing and exhaust manifolds are non-smog.


29
Restoration / Re: 67-68 shifter rubber donut
« on: February 13, 2012, 06:00:08 AM »
I have a bunch of the orange detent covers that I bought from the original supplier. I'm willing to part with some/most.

Martin

30
Originality / Re: Correct Hood Catch & Plate Fasteners
« on: January 19, 2012, 05:45:05 AM »
I bought my 68 LOS Camaro in 1990 and had to go throught this same thing. The front end was changed and hardware store fasteners were used. I made lots of trips to salvage yards and finally found all the correct fasteners for the sheetmetal. I also verified them from looking at original cars at Pomona and Long Beach swap meets. RBW and an anchor were seen in 67 and 68. More anchors in 67 and few in 68. In 69 I saw more of the C fasteners. This is mostly the bolts for the fenders to inner fenders, upper round braces, hood latches and radiator support. The bolts into the firewall are different. You need to spend time looking at the AIM and a car to see what part number goes where and how many you need. I have that for the 68 standard front end but it's probably not in a publish ready format.

Martin

Pages: 1 [2] 3 4 ... 9