Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - copo

Pages: 1 ... 3 4 [5] 6 7
61
Decoding/Numbers / Re: 837 Stamp
« on: February 05, 2012, 03:32:15 AM »
Re-stamp, the #7 stamps have the incorrect fonts and not known stamp date.

62
Originality / Re: Dash Panel Mystery
« on: January 21, 2012, 07:36:22 PM »
That PANEL, INSTRUMENT" part number: 8716458, group: 10.230 is for a Nova, I am not sure what year it fits, but going by the speaker grill opening I would say mid to late 70's.


63
Restoration / Re: Correct cowl hood relay screw
« on: January 01, 2012, 08:02:11 PM »
The screw is listed in the AMK catalog with there part # B-12049.

64
Restoration / Re: 69 Rear Bumper Guards
« on: September 03, 2011, 10:49:54 PM »
The correct bolt size for tail panel is 5\16 NC, the 3/8 bolts are for attaching upper mounting bracket to the bumper guard.

65
Decoding/Numbers / Re: Rear axle tube codes and engine codes
« on: August 11, 2011, 11:52:46 PM »
My 69 COPO has the rear end with the same build date and engine build date of May 21 69.

66
Originality / Re: Brake hoses
« on: August 01, 2011, 11:24:30 PM »
The  Raybestos. InLiine Tube hoses are not the same as the original hoses. The original hoses have a square end on the banjo fitting, the InLlne tube and Raybestos hoses have rounded corners on the banjo fitting. The hoses in the auction have the correct square end banjo fitting.

67
I use to own a original 69 DZ engine with 618 block with a casting date of A-15-69 and and a assembly build date of V0508DZ.

68
1969
Norwood
06A-Month and week of vehicle assembly
427-Engine
M22-Transmission
49.5-Driveshaft length (measured center of u joint to center of u joint                                                                                                   
3790024- Driveshaft casting number
strap and bolts-Type of attachment to pinion yoke.
BE 0610 G2- Code stamped on front of passenger side axle tube.
N/A-Paint stripes
in-line-Position of the u-joint flanges on each end are in line.

69
General Discussion / Re: Front Bumper Guard Install
« on: February 13, 2011, 10:13:38 PM »
I checked my 69 NOS front bumper guard kit, instructions show the template from the center line of bumper to the inside edge of the bumper guard is 7 inches.

70
Decoding/Numbers / Re: Correct date range
« on: February 03, 2011, 07:14:16 PM »
The 2 real 837 dates I have seen that would fit your cars build date is March 24, 69 and April 3, 69.

71
Restoration / Re: Pressed in bumper nut
« on: September 20, 2010, 06:51:54 PM »
I have a used spare from a old fender extension if you are interested in it.

72
Originality / windshield washer spray nozzle
« on: August 06, 2009, 08:40:15 PM »
I was looking up the part number for the windshield nozzle in my 67-70 GM camaro parts book, I noticed there were 2 part numbers listed for the nozzle.
# 3886973 -67-69 all except ducted hood.
# 3983947- 69 all with ducted hood.
Does anyone if there was a different nozzle used with the cowl induction hood.

73
Research Topics & Reports / Re: Gas tank date codes
« on: July 12, 2009, 12:56:04 AM »
Just to add my input, I looked at the tank I removed from my 69 05E, stamped 69  41.

74
Research Topics & Reports / Re: 69 decklid emblem holes
« on: July 25, 2008, 12:24:21 AM »
69 NOR, Z28, 05E (shipped June 4 69) trunk lid stamped dated T 20, two sets of emblem holes.
69 NOR, COPO, 06A, factory installed spoilers, (shipped June 24 69) trunk lid stamped date T 17, one set of emblem holes.

75
I have a original 837 with build date of 9-E-23 with stamped CZ with the # 3 under it. I know the stamp is orginal as the alternator was early take off and it has never been restored.

Pages: 1 ... 3 4 [5] 6 7