Messages

46

Originality / Re: Radio delete cover screws question.

« on: April 20, 2013, 01:48:48 AM »

I checked the screws from my original radio delete plate, the screw assembly is a  # 8-18 x 5/8 '' long,  5/16 hex head with rbw head markings, with a attached 5/8'' flat washer.

47

Originality / Re: 1969, which pinion snubber

« on: March 13, 2013, 05:30:20 PM »

Are you sure this one hasn't been replaced? The reason I'm asking? This bolt on wedge type is what most vendors were selling when I built my car last year and I had to use my old one.  Mine was in good shape but I wanted a new one and they didn't sell them then.

No, My old 69 Z28 (05E) that I purchased in 1983 had the same bolt on wedge snubber.

48

Originality / Re: Carb Stud Length - '69 Cowl Air Cleaner

« on: March 10, 2013, 07:03:45 PM »

In the AMK products catalog it shows the stud with part 3747933 as 1/4 20 x 1 5/8 OAL. This part number of the stud # 3747933 is listed in the cowl induction section of the AIM. This length of the stud appears to match the original engine photo of the # 3 ZL1 camaro in a book I have.

49

Originality / Re: 1969, which pinion snubber

« on: March 10, 2013, 06:42:23 PM »

bolt on wedge
12 bolt BE 4:10
L72  M22
NOR 06A

50

Restoration / Re: Engine painting poll

« on: August 19, 2012, 09:51:17 PM »

The bracket in the bottom photo with the rounded corners is the correct bracket for 68-69 B/B. The rounded bracket in the above photo is correct for 70 B/B because the bracket was drilled for a return spring. The 68-69 B/B bracket did not have hole drill in it for return spring.

51

Originality / Re: Screws for shifter trim plate.

« on: July 30, 2012, 02:03:44 PM »

They are listed in the AMK catalog as chrome plated screws 8-18x 7/8 .31 OD, # B-11150.

52

Originality / Re: Speedo cable Clips

« on: July 21, 2012, 05:58:42 PM »

I compared your clip to a original spare clip I have and I could easily bend my clip to same configuration as yours shown in the photos.

53

Originality / Re: Speedo cable Clips

« on: July 21, 2012, 02:59:01 AM »

It l looks like standard clip that has been bent around 180 degrees to me. 

54

Originality / Re: Looking for another decal project to consider

« on: July 10, 2012, 06:15:21 PM »

How about doing the 69 396 /375 hp Emission Decal.

55

Originality / Re: Original Battery Hold Down Clamp

« on: June 23, 2012, 01:49:35 AM »

Thanks for the information on the bolt.

56

Originality / Re: Original Battery Hold Down Clamp

« on: June 21, 2012, 05:12:03 PM »

I would like know that is the length of hold down bolt shown in the photos.

57

Restoration / Re: Looking for 1969 Column Shifter PRNDL parts

« on: June 13, 2012, 09:42:48 PM »

I checked my cluster and the dash PRNDL assembly is there, but the orange needle is broke off the plastic arm too.

58

Restoration / Re: Looking for 1969 Column Shifter PRNDL parts

« on: June 12, 2012, 05:46:18 PM »

I have spare cluster that that has column shift assembly, I am not sure if it is complete or not. Could you post photo of the piece you need.

59

General Discussion / Re: Was This Ever a Recall?

« on: April 04, 2012, 05:52:04 PM »

I checked my 69 camaro wiring harness and it does not have a harness retaining wiring clip in this location.

60

Originality / Re: ZL2 Flat Bottom AC Base

« on: February 21, 2012, 11:07:52 PM »

Exactly what the difference is between an SS350 manual base [6485233] and the Z/28-BB base [6485235] I do not know.

The difference is the between the SS350 manual base is the vent tube has a sharper 90 degree bend to the base of the of the air cleaner. The tube are the same size.