Messages

16

General Discussion / Fly me to the moon movie

« on: July 21, 2024, 05:26:09 PM »

Channing Tatum drives a 67 SS Convertible, there’s a bunch of car scenes and it’s a good movie. Watch the trailer and decide for yourself.

17

General Discussion / Re: Let's help my neighbor correct his 68 RS engine bay

« on: July 08, 2024, 05:13:24 PM »

Do you mean cosmetically correct to factory delivery? As in replacing the valve covers hold downs, fuel filter, etc?

18

1969 - Orphans / Re: M-21 VIN 19N622751 on MarketPlace!

« on: June 26, 2024, 06:53:22 PM »

That 6 appears to be a 9....

19

Decoding/Numbers / Re: 3917291 info/help

« on: June 21, 2024, 02:03:25 AM »

It’s hard to see if any work has been done on the heads without pictures inside the valve entry area. Some of those push rods have been reinstalled 180 by looking at them. Probably makes no difference….I’ll let the engine pros chime in.

20

Originality / Re: 1967 SS350 Smog pump info help needed

« on: June 20, 2024, 04:02:52 PM »

Doesn’t the AIM show the part number?

21

General Discussion / Re: Fold Down Rear Seat

« on: June 20, 2024, 02:22:08 AM »

Dave, after reading this, I found the picture I meant to upload….

22

Restoration / Re: 293 BR coil index

« on: June 02, 2024, 03:46:32 PM »

My point exactly. Picture shows proper orientation, NOT. It appears there are many errors in the manual and I speculate nobody outside the judging circle of trust read it before print. I would go with the printed instructions and not the picture.

23

General Discussion / Re: Fold Down Rear Seat

« on: June 02, 2024, 03:40:04 PM »

It definitely has a useful purpose in a parade.

24

Decoding/Numbers / Re: 124379N590136

« on: May 22, 2024, 02:56:38 AM »

Damn, pretty soon we'll have to start paying for matching numbers cars

25

Originality / Re: trunk mat

« on: May 15, 2024, 07:10:25 PM »

Pretty sure there is 1 supplier for most of the reproduction parts in most cases. You'll have to make the best of it. Take your time and trim it Pretty.

26

Originality / Re: Spare tire

« on: May 06, 2024, 04:48:01 AM »

Here’s a 3d plastic printed version. I’m trying to find a local printer for a metal part for authenticity visuals, and no work required to sand out the 3d lines.

27

Originality / Re: Spare tire

« on: May 05, 2024, 05:03:56 AM »

I have the STL file and can get one 3d printed if you need. Plastic is cheap, but I’m trying to source a metal printer. PM me if you want  to discuss further.

28

Originality / Re: Wiper motor stamping

« on: May 03, 2024, 05:33:20 PM »

Indy: I find it interesting there is no spacing on the stamp. Probably because it was stamped with something.

Can't repeat: Definitely a different font. It appears an8 band stamper with letter on the end are applicable some of the time.

29

Originality / Re: Wiper motor stamping

« on: May 02, 2024, 03:24:53 AM »

The original one quit sometime in the late 80s, and I had a service replacement installed. I picked up this one from Pace Car Jeff last summer.

30

Originality / Re: Wiper motor stamping

« on: May 01, 2024, 04:52:40 PM »

Definitely different fonts and I'm thinking the stamp wasn't given much thought,  as long as it made it on the part.