Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - R68GTO

Pages: [1] 2 3 ... 13
1
General Discussion / Re: Wrong body tag?
« on: April 28, 2024, 11:00:08 PM »
My old 09D COPO is body number 108154.  It was final assembled on 9/26/69

2
Restoration / Re: 1969 Camaro front spoiler support rods
« on: April 20, 2024, 11:16:43 AM »
When was your Z built (month/year)?  Spoilers were standard after April 69? on Z28 models.  D80 on the data plate? My COPO was a non-spoiler car originally.  Front/rear spoilers added by 1971.  The guy that added them installed the spoiler support rods on the front so it had a hole in the front subframe.

3
Decoding/Numbers / Re: 1969 seatbelts
« on: March 10, 2024, 01:09:27 AM »
weeks 36 and 37 for an 09D

4
Maintenance / Re: Adjust Steering
« on: February 28, 2024, 11:51:59 PM »
I can't find the specific one back that I used, but I do recall it wasn't the exact box I had.  Saginaw's design, rebuild, adjustment for manual boxes were similar across multiple applications.

5
Maintenance / Re: Adjust Steering
« on: February 27, 2024, 11:50:19 PM »
I rebuilt my manual steering box and adjusted it out of the car to get it close then made small final adjustment after re-install.  It's really important to get it "centered" in the travel. 
Out of the car the force required to rotate the input should noticeably get higher when you approach the center of travel, with the highest resistance at dead center of travel.  Once back in the car, I loosed the nut and adjusted the bolt just slightly to stiffen it up to my liking.  Since you're not sure how it got loose, I would pull it and try to reset it on the bench, then re-install and see if it got better. There are some good Youtube videos on rebuilding and setting these Saginaw units.

6
Restoration / Re: Inner fender cup washers and bolt colors
« on: February 27, 2024, 11:41:20 PM »
I believe that is correct.  When I stripped my low mile fender washers, you could see the pattern of black dip-painting....one spot had thick paint that virtually filled the edge of the recess on each one

7
Restoration / Re: brake booster delco logo question
« on: January 24, 2024, 11:35:23 PM »
As far as I know, all originals were upside down (weak) and on lower LH side as viewed from the front of the car.

8
General Discussion / Re: My story and why to not give up looking.
« on: January 24, 2024, 11:31:25 PM »
Great story, congrats on filling in the gaps!

9
Original Cars and Details / Re: Yard find 1969 Z/28 RS
« on: January 19, 2024, 11:23:15 PM »
Curious about the block pad....I thought those were masked to not hide the stamping with paint or is that only when the VIN is on the pad?

10
Originality / Re: 69 Center axle bumper - two styles?
« on: January 10, 2024, 12:44:12 AM »
Maybe they had a special tool to install the push in style - based on my experience, the giant PITA of getting the push-in style installed would be enough reason to change to bolt-in style.  Bolt in add complexity, but if it reduces time, it might have driven a change.

11
Originality / Re: 69 Center axle bumper - two styles?
« on: January 04, 2024, 11:17:25 PM »
Mine is an X44 COPO BE rear.

Just a pure speculative theory on this topic.  We have the change document that notes the move to bolt in style.  For late build cars (past normal production end date of July time frame), they may have received old style or a mix due to limited availability of new style bolt in.  I wonder what the design is of the 1970 Camaro snubber.....same bolt in, different bolt in, or push in?

12
Originality / Re: 69 Center axle bumper - two styles?
« on: December 31, 2023, 10:08:11 PM »
My 09D (late) Norwood has the holes for the screw in style but had a push in style installed when I took it apart for restoration.  Every bumper on the car was original when I took it apart.  This one ws one of the few on the car I couldn't save - it was rock hard and had to be destroyed to get it out.

13
Originality / Re: Misc markings and labels
« on: December 23, 2023, 12:20:13 PM »
I found similar markings on my 15,000 mile car.  Mine had 2 inspection tags on the heater box and had similar grease pencil number.  My understanding is the handwritten number is an assembly sequence number.  Mine had a "3" and I found the same "3" on top off my gas tank.  I did not find any yellow tape.  Steering column and gauge cluster tags are the "norm" for identifying applications for those components. 
Sounds like you have a really cool Z - post some pics!

14
Original Cars and Details / Re: Yard find 1969 Z/28 RS
« on: December 17, 2023, 01:07:53 PM »
Great way to create suspense and anticipation Joe!  I, for one, am looking forward to the pics!

15
Restoration / Re: Late 69 standard bucket seats
« on: December 12, 2023, 12:40:18 AM »
no, plain hole.  Appears to be punched and has the same finish as the surface.  Definitely doesn't look like anything has ever been in there.  Here's a closer pic.

Pages: [1] 2 3 ... 13