Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - hugrz28

Pages: [1]
1
General Discussion / Re: Bolt torque two piece rotors
« on: November 13, 2018, 04:35:42 PM »
Thanks Tim

2
General Discussion / Bolt torque two piece rotors
« on: November 13, 2018, 02:31:09 AM »
Does anyone on the forum know the bolt torque for two piece rotors? Specifically the five bolts that attach the rotor to the hub.

3
General Discussion / Re: 1969 Camaro Fiber Optics
« on: March 16, 2018, 07:11:16 PM »
While cleaning up my fiber optic housing I noticed a copper tone paint mark on the fiber optic cable and the black rubber housing. It was on both sides (left & right) and seems to indicate the headlamp fiber cable and the the center lamp on the housing. Has anyone seen this before? See the attached picture. 

4
General Discussion / Re: 1969 Camaro Fiber Optics
« on: March 06, 2018, 05:05:38 PM »
Wow, have never seen one of those before......awesome!

5
General Discussion / Re: 1969 Camaro Fiber Optics
« on: March 06, 2018, 04:37:39 PM »
Thanks Ed!

6
General Discussion / Re: 1969 Camaro Fiber Optics
« on: March 06, 2018, 04:11:37 PM »
Very nice convertible set, those are hard to come by. Does anyone know where you can get the ferrule, connector that goes on the end of the fiber optic cable? It retains the cable inside the front fender light monitor. I'm missing a few.

7
General Discussion / Re: Exhaust Tip Finish
« on: March 06, 2018, 03:41:08 PM »
Great information........thank you!

8
General Discussion / Re: Exhaust Tip Finish
« on: March 06, 2018, 04:32:05 AM »
Hi William,

Thanks for the reply. I had my exhaust re-done about thirty years ago and it's not GM but is a coated steel. Many people told me that the tips should be chrome (stainless) and I couldn't find any documentation to support this. Thanks you for clearing this up!

9
General Discussion / Re: 1969 Camaro Fiber Optics
« on: March 06, 2018, 04:28:22 AM »
Thanks Jim, I'm glad I took your advice and joined. Thanks to those who have posted on this thread, I look forward to sharing and learning. I will post more picture's of The 'Z' in the next week. I'm a died in the wool Trans Am follower (the early days) and look forward to learning from the experts who were there.

10
General Discussion / Exhaust Tip Finish
« on: March 05, 2018, 11:55:50 PM »
Hi,

Does anyone know the correct exhaust tip finish that was used in the mid year exhaust change? Specifically for a car built in Feb., March 1969 which has the single cross flow muffler. I've seen many old photos that show it to be bare steel. Appreciate any help.

11
General Discussion / Re: 1969 Camaro Fiber Optics
« on: March 05, 2018, 11:47:23 PM »
Hi Ed,

Thanks for the quick reply. Well, there is question I've had for thirty-seven years put to rest.

12
General Discussion / 1969 Camaro Fiber Optics
« on: March 05, 2018, 11:01:30 PM »
Hi,

New to the site and also a first time post. Long time owner of a 1969 Z/28 that came with fiber optics. My car was built in March 1969 at The VanNuys Plant and sold at Guardian Chevrolet in Brea, CA. I've been looking for info. on the use of a 'black plastic gasket' that sits between chrome bezel and the fender. I've been told that the 'gasket' was only used on Norwood, OH built Camaro's with fiber optics. In over thirty years I have found no factual information to support that Norwood only Camaro's used this gasket. There is nothing in The AIM that shows it use. Any insight would be greatly appreciated.

Dan
 

Pages: [1]