Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ALLZS

Pages: [1] 2 3 ... 9
1
Originality / Re: REAREND AXLE CODE & DATE STAMPING
« on: January 04, 2024, 05:44:07 PM »
THE CAR HAS ITS ORIGINAL ENGINE & TRANSMISSION ALSO THE ORIGINAL PROTECTO PLATE  HOPEFULLY OTHERS WILL CHIME IN 

2
Originality / Re: REAREND AXLE CODE & DATE STAMPING
« on: December 06, 2023, 09:29:13 PM »
trying to remember the posi code thinking H-7 - G or  H HAVE TO LOOK THROUGH PICTURES  i do have the original p o p the car is a 4 th week of  sept 1968 build

3
Originality / Re: REAREND AXLE CODE & DATE STAMPING
« on: December 06, 2023, 07:18:58 PM »
the posi carrier date is within the build date the ring and pinion was changed by the 2nd owner to 411 gears that where dated 7-71 , this rearend is in my 69 camaro

4
Originality / Re: REAREND AXLE CODE & DATE STAMPING
« on: December 06, 2023, 01:30:33 PM »
still looking for rearend stamps off set anomalys

5
Originality / Re: REAREND AXLE CODE & DATE STAMPING
« on: November 29, 2023, 04:46:35 PM »
thanks for uploading the pictures if anyone has any pictures of similar stampings especially in that build date time  frame it    would be greatly appreciate  thanks

6
Originality / Re: REAREND AXLE CODE & DATE STAMPING
« on: November 29, 2023, 02:52:14 PM »
 I E MAILED YOU SOME PICTURES

7
General Discussion / Re: REAREND BUILD SEQUENCE
« on: November 29, 2023, 02:18:16 PM »
SO THE HOUSINGS WHERE CAST  BY A GM FOUNDRY AND EATON SUPPLYED THE INTERNALS AND GM BUILT THE UNITS IN HOUSE   

8
General Discussion / REAREND BUILD SEQUENCE
« on: November 28, 2023, 08:13:12 PM »
I KNOW THE REAREND HOUSINGS WHERE CAST BUY EATON BUT WHERE THEY ASSEMBLED THERE OR WAS THAT DONE AT THE GM FACTORY

9
Originality / REAREND AXLE CODE & DATE STAMPING
« on: November 28, 2023, 08:11:11 PM »
I HAVE A EARLY BUILD CAMARO  12 BOLT AND IT LOOKS LIKE THE AXLE CODE AND BUILD DATE WHERE NOT GANG STAMPED BUT INDIVIDUALLY STAMPED  WAS THAT POSSABLE

10
Originality / 4 speed shifter rod mounting
« on: May 17, 2023, 12:18:01 PM »
on a 69 Camaro hurst shifter where the shift rods attached to the shifter and shift levers  with a cotter pin or a snap in clip

11
Originality / Re: NEGITIVE BATTERY CABLE LEAD LOCATION
« on: May 06, 2023, 02:42:47 AM »
I FOUND MY ANSWER IT DOES GET MOUNTED TO THE CORE SUPPORT

12
Originality / Re: NEGITIVE BATTERY CABLE LEAD LOCATION
« on: May 04, 2023, 08:45:28 PM »
I don't know what battery was in it from the factory

13
Originality / NEGITIVE BATTERY CABLE LEAD LOCATION
« on: May 04, 2023, 06:41:02 PM »
on a early build 3 week of sept 68 where is the small wire off the negative battery cable mounted  to is it  the fender or the core support

14
Originality / ENGINE LIFT HOOKS
« on: May 02, 2023, 12:31:20 PM »
on  aluminum  intake  engines where the lift hooks natural steel or zinc plated 

15
Originality / NEGITIVE BATTERY CABLE
« on: April 21, 2023, 10:17:15 PM »
ON A EARLY BUILD SEPT OF 68  3 WEEK  WAS THE SMALL GROUND WIRE OFF THE BATTERY CABLE GROUNED TO THE PASSANGER FENDER OR THE CORE SUPPORT

Pages: [1] 2 3 ... 9