Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Ue

Pages: [1] 2 3 4
Maintenance / Re: 68 Tilt column loose & turn signal switch removal
« on: June 01, 2016, 10:42:01 AM »
Ok, an update for anyone looking for info in the future...

Getting the switch cover off was a real pain. I ended up forcing it up with flat head screw drivers in the hazard switch & turn signal holes. I damaged it and had to get it repaired which was costly due to the exactness of the shape for it to fit back on (and still look like original).

Once the turn signal housing and the switch assembly was removed, remove the 2 pins (I screwed a screw into them and GENTLY used vice-grips to pull them out.
After all that it was pretty easy to get to the 4 loose bolts.
You can tighten the knuckle at the same time if you're game but mine was still Ok.

Make sure you clean off all the old grease and redo with fresh grease before reinstalling the knuckle. Don't get grease on the tilt lock area though or it'll slip later on.

TIP - Use some lock-tight when refitting as you don't want to have to do this twice in a lifetime!.

Feel free to reply to this post if you want some more pics to see what you're going to be looking at.

Maintenance / Re: 68 Tilt column loose & turn signal switch removal
« on: January 24, 2016, 12:24:28 AM »
Thanks Ramjett54.

Do you have the links to the references mentioned? The hyper links didn't come through in the document you linked to for me.

"This paper makes reference to Descriptions #5, #6, & #7.  They are included on two pages of line drawings entitled GM A-Car 1967-68 Tilt Steering Column Page #2, & #3.  "

I was able to find the link to this one below...
"Also there is a schematic drawing entitled GM A-Car 1967-68 Tilt Steering Column Blowup.  Most steering column parts will be called out with a reference number from this blowup. "

Maintenance / Re: 68 Tilt column loose & turn signal switch removal
« on: January 21, 2016, 10:08:03 AM »
Thanks 69Z28-RS,
No chance of finding a Chevy factory tool down here in Australia unfortunately.

A great bloke (Jim Shea) gave me some advice via email and I've made a tool to remove the cover but it's stuck on so tight it's bent the tool (as you can see in the pic). I'm now trying to find someone to make one out of stiffer steel and try again though I'm pretty sure it'll just unroll the lip.

Here's what Jim Shea sent me for future forum reference......

Method 1
Remove the turn signal lever, hazard warning button, and turn signal switch.  Now take two fairly large tools (such as screwdrivers) and insert them through the turn signal lever and hazard button windows in the Housing can.  Now try to carefully pry the Housing can up and off the Housing Assy.
Method 2
If the above pry bar method doesn’t work, here is a tool that can be fabricated to remove the cover.  The link shows the tool that is designed to slip under the rolled lip of the cover to remove it.                                 

It uses a steering wheel puller and three circular sheet metal parts that make up the tool.  All three sheet metal parts were made from electrical conduit box covers.  The circular plate with the nuts attached is smaller in diameter than the inside diameter of the rolled lip of the cover, so it will slip down inside.  The two half-moon parts are larger in diameter than the circular plate and large enough to fit under the lip of the cover.  But since they are split, you can work each one individually down inside the cover and under the rolled lip.
Place the circular part inside the cover with the nuts on the underside.  Now work the two half-moon parts down inside.  Align the bolt clearance holes in the half-moon plates with the nuts on the circular plate.  The puller should have a nut threaded on each of the two bolts.  Thread the puller bolts into the nuts on the circular plate.  Tighten the upper nuts down against the half-moon plates and the circular plate.  Use the puller to draw the cover off of the housing.

Maintenance / Re: 68 Tilt column loose & turn signal switch removal
« on: January 14, 2016, 11:54:13 AM »
This is the tool...It hooks under the rolled lip.

Maintenance / Re: 68 Tilt column loose & turn signal switch removal
« on: January 14, 2016, 07:10:48 AM »
It's great to see so many people checking to see if they can help me out here.
Thanks for no one replying "3 screws" like some others did when I posted this question to a Facebook group. CRG members are smarter than that. :)

Just incase you're wondering, even after removing the 3 screws that hold the turn signal switch in place, it can't be removed as the rolled lip of the column + flasher screw keep it from coming out (as per the red circles in the pic in the first post).

I've read various online guides about similar year tilt columns but some say rotate clockwise, others say rotate anti-clockwise, while some say to pull it straight off. I can't find anything that mentions a 68 Camaro tilt column so would really appreciate ANYONEs advice here.

Maintenance / 68 Tilt column loose & turn signal switch removal
« on: January 10, 2016, 03:04:57 AM »
What do people use to remove the turn signal switch cover on a 68 Tilt colum if you don't have Tool-J-22708?
I tried a steering wheel remover using the bolt heads to hook under the rolled lip of the cover but it just unrolled the lip.

Hey All,

What car cover do people recommend to keep out the dust while stored in garage?

I see there are many around but are looking for a fitted cover to use while the car is stored in a garage.

If this has been discussed elsewhere, please just add the link to the topic/thread.


General Discussion / Re: 68 rocker molding trim clips
« on: March 19, 2015, 08:17:39 AM »
Special Thanks to Victor!

For anyone looking at this thread in the future, Here's the pics Victor sent me...
Hope this helps future RS restorers.

Suppliers have them.

Camaro Central
1968 Molding Clips Kit, Rocker Panel, Rally Sport, OE Style
Part # BCM-18B

Classic Industries

General Discussion / Re: 68 rocker molding trim clips
« on: March 18, 2015, 10:05:49 AM »
Hi Victor.
I PM'd you if you have the chance to reply with the pics.

Do the correct clips look like this??

General Discussion / Re: 68 rocker molding trim clips
« on: March 14, 2015, 09:43:32 PM »
Hi Guys,  I know this is an old topic but I want to know what the original 68 RS molding clips look like and the pics above are no longer available to be viewed. Can anyone repost an original clip please?

Mild Modifications / Re: Stinger Hood for my 68 in Australia
« on: February 08, 2015, 05:22:30 AM »
Hahaha, I meant the faux opening at the front of the stinger style hood cowl.

Mild Modifications / Stinger Hood for my 68 in Australia
« on: February 03, 2015, 09:03:45 AM »
Hi Guys,

Who can recommend a high quality Stinger Hood for my '68?

Please tell me why you recommend one particular brand and for the Aussie CRG guys & gals, let me know who to import it from.

Also, has anyone cut out the opening at the front rather than rely on the cool air induction from the back of the hood? Those ducts are screaming "cut me free!" I reckon.

We don't see many with Stinger hoods down under so I'm wanting to be a bit different.

Originality / Re: 68 SS RS Wheel well moldings
« on: August 28, 2014, 09:04:46 AM »
Thanks Rick. I love how helpful and informative this site and everyone who uses it is.

Here's the link for future readers...

Now, can anyone confirm that a 11B 68 RS would have the trimmed front wheel well molds?

Originality / Re: 68 SS RS Wheel well moldings
« on: August 22, 2014, 09:55:24 AM »
OK, going to kick this thread off again...

Would a 68 RS Camaro (build Nov 67) front wheel arch mouldings stop at the rocker molding or continue down to the bottom of the wheel arch of the rear of the front guard?

This thread states there was a "discontinued" style. -

If so, does anyone have a detailed picture or template for me to cut my classic Industrie repos?

If not, does anyone have a picture of the rocker moulding meeting up with the wheel arch mould?
A (poor) example is below.

Cheers, Ue.

Originality / Re: 68 Transmission Tunnel cut out identification
« on: August 20, 2014, 11:47:04 AM »
Thanks Guys.

Pages: [1] 2 3 4