Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - WorkinProgress

Pages: [1] 2 3 ... 11
1
General Discussion / Wittek Hose Clamp Size
« on: November 08, 2018, 10:44:11 PM »
Does anyone have their original Wittek hose clamps for the heater hoses on their car? I heard they used two sizes, 1 1/16" and 1 1/8". If anyone has original hose clamps I would like to know for the '69 Camaro, big or small block and what plant car was built at and build date.

                                                                      Thanks, Warren

2
Decoding/Numbers / Re: Caveat Emptor...altered/swapped tag
« on: October 26, 2018, 01:10:26 AM »
Wasn't there an early tag for sale recently and everyone was questioning when did the D80 on the tags start. This might have been the tag.

                                  - Warren

3
1969 - Orphans / Re: 1969 Muncie Vin 19N676518 on CL Malvern PA
« on: October 25, 2018, 02:31:23 AM »
Has one groove on the input, so it is a M21.

                            - Warren

4
Originality / Re: Holley Dual Feed Fuel Line Y-Block
« on: October 25, 2018, 02:22:34 AM »
I have never seen any manufacturers markings on the '69 Z/28 fuel block.

                                                         - Warren

6
Originality / Re: 69 L78 engine lift hooks
« on: October 17, 2018, 03:10:53 AM »
Lawrence,

All B/B '69 Camaro's came with engine lift hook brackets. The front hook bracket is painted silver on the L78, and L89. I believe the rear bracket is bare.

                                                    - Warren

7
1969 - Orphans / Re: 19N709366 M21 on N.Y. C/L
« on: October 14, 2018, 05:41:29 PM »
Checked the VIN 124379N709366 on VinAudit.com and they have history on the car. Now we know it is a coupe and the car may still exist.

                                               - Warren

8
1969 - Orphans / 19N709366 M21 on N.Y. C/L
« on: October 14, 2018, 04:41:12 AM »
1969 Camaro M21, date stamped P9R21B

VIN stamp 19N709366     VIN 124379N709366 OR 124679N709366

Located Pawling, NY

For sale $1,900.00          Call 845-742-2770         Advertised on Craigslist.

Has the later '661 main case, which is correct for the late build '69 Camaro's

https://hudsonvalley.craigslist.org/pts/d/muncie-m22-rock-crusher-4/6718982457.html

9
Decoding/Numbers / Re: 68 Dash Vin Holder Replacment
« on: October 02, 2018, 04:49:15 PM »
Well now we know what you need. If that lower reinforcement plate is missing, you should be able to take a piece of sheet metal and cut it to the size of your VIN tag, drill two holes and rivet it. You will not see that from the top of the dash. I am sure that just keeps the VIN plate from sagging on the dash. There may even be someone on the site that has the plate for you.

                                                            - Warren

10
Decoding/Numbers / Re: 68 Dash Vin Holder Replacment
« on: October 02, 2018, 04:23:31 AM »
So what is the problem with riveting it back to the dash? Pictures help a lot if you can post them.

                                                   - Warren

11
Decoding/Numbers / Re: 68 Dash Vin Holder Replacment
« on: October 01, 2018, 10:24:57 PM »
Hey Tim,

Welcome to the CRG!

Has the entire top of the dash been removed? If it has, was another top panel installed? The top of the dash should have a slot for the VIN to show through. Is that slot there on the driver's side?

                                  - Warren

12
Decoding/Numbers / Re: Caveat Emptor...big problems
« on: September 22, 2018, 11:01:19 PM »
Here is their website, with the car in the sold section......

http://zubesimportauto.com/advert/69Z/album/index.html#

                                               - Warren

13
General Discussion / Re: 1969 Camaro Z28 distributor 1111480
« on: September 22, 2018, 05:16:47 PM »
Question.

Why a lot of the 1969 Camaro Z28 distributors (1111480) seemed to get traded out with something else back in the day?

Because when you popped your hood. it was cool to show off to your friends the aftermarket parts, for bragging rights.

                                                                          - Warren

                                                 

14
Decoding/Numbers / Re: 3970010 engine decode help
« on: September 11, 2018, 05:23:03 AM »
It is a truck engine. 1975 350, 165hp, 4 barrel

                          - Warren

15
General Discussion / Re: trim rings
« on: September 07, 2018, 01:01:49 AM »
The '67 Corvette 15 X 6 four clip trim rings are the same ones used on the '69 Z/28 15 X 7 wheel.

                                                           - Warren

Pages: [1] 2 3 ... 11