Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - 68Z22

Pages: [1] 2
General Discussion / 68 Trunk Mat
« on: September 07, 2015, 05:02:06 PM »
Installing a new trunk mat in my 68,I am not sure how to cut were the fuel filler tube is.
My original mat is very deteriated and brittle.
Can some of guys post some pics of your trunk mats,most specifically around fuel filler tube.
Thanks in Advance.

Restoration / 68 A6 A/C Compressor Rebuild
« on: December 28, 2014, 10:34:33 PM »
I need to have my original 68 A6 AC Compressor rebuilt and restored to complete my restoration and get the AC working.I am Looking for suggestions on who rebuilds compressors.

Decoding/Numbers / Re: 68 camaro 7 blade fan 3931002
« on: December 28, 2014, 10:14:35 PM »
My 68 Camaro RS 327 / 275 with factory AC,Auto,has the 7 blade fan 3931002.I believe it is the original to the Camaro. My car was mostly original and unrestored when I purchased it years ago.

I used these guys when I shipped my Camaro from the Great State of GA. to the Great State of PA..
Great personalized service at a fair price.I plan on using them when the car is complete and ready to ship back to GA.

Maintenance / Re: AC compressor
« on: August 21, 2011, 11:03:11 AM »
My 68 has been parked since 1983 , A/C Working when Parked.

I am also looking for someone how can Rebuild My A/C Compressor.

Any Recommendations on Vendor ?

Restoration / Re: a/c compressor restoration
« on: December 19, 2010, 01:38:09 PM »
I had what they called a restoration on my O.E. condinser.
Which consisted of pressure check,straighten fins,and refinish.

What I got was a pressure check and what looks like rattle can paint and very little to no fin restoration !

I am glad I did not send my whole A/C system for restoration !

Here  is a pic , Make your own opinion !

Restoration / Re: a/c compressor restoration
« on: December 18, 2010, 12:35:18 PM »
I was not pleased at all with the Quality or lack of Quality with the before mentioned vendor.

I would recommend finding another a/c restoration vendor.

Just my opinion !

Restoration / Re: Polishing and Buffing Aluminum
« on: October 22, 2010, 11:57:54 PM »
I Would Like to here from a ACAA Judge on this topic.
Or even better From Lucas Restoration Since they prepaired that Fantastic "Top Flight" 68 RS/SS that was at the
2010 Camaro Nationals @ Carlisle.

Restoration / Re: Polishing and Buffing Aluminum
« on: October 21, 2010, 12:14:58 AM »
Since all the aluminum was anodized from the factory and when most Camaro's are restored the aluminum trim is polished,What would be correct for a Judged points car?
Polished and Sealed or,
Anodized as it was from factory or,

General Discussion / Dual Exaust or Single Exhaust ?
« on: October 10, 2010, 09:08:00 PM »
Trying to determine which exhaust my 1968 Camaro RS came from the factory with,As usually the original factory Exhaust is long gone and had been replaced with headers and after market mufflers and dual pipes.
I am doing a complete restoration and returning it back to factory specs.
The restoration shop raised the question about the exhaust ,single or dual exhaust.
I do not have the factory build sheet to know what it came factory with.
Would the block numbers (327/275) indicate anything,or what about the Trim Tag ,V.I.N.
I have looked in the AIM and can't totally make sense of it.I have been told that certain holes in the rear frame rails can determine which exhaust it came with.
Any feed back would be greatly Appreciated.

General Discussion / Re: Heat Rise tube
« on: September 28, 2010, 10:45:27 PM »
Here is one on EBay If any one may still be looking,


General Discussion / Re: Heat Rise tube
« on: August 05, 2010, 09:16:21 PM »
Is this what your Looking for?

Restoration / 68 Deluxe Door Panel Repair
« on: April 10, 2010, 09:08:41 PM »
Wanted to know if anybody has had any exprience in repairing cracks or splits in the arm rest portion of a deluxe door panel ? Or what would be even better if anyone knows of a Vendor who makes the kind of repairs ? Any advice would be greatly appreciated.

Originality / Re: 68 Heat Stove Finish
« on: February 19, 2010, 10:31:55 AM »
Thanks for all the replies on this topic.Galvinized heat stove was my instinct also,It is great to confirm that.

Pages: [1] 2