Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - revdan49

Pages: [1] 2
1
General Discussion / Re: correct steering column bowl
« on: March 26, 2009, 02:38:30 PM »

That's perfect ! It's exactly what I was looking for. Thanks for your time, and effort.

2
Restoration / Re: steering column
« on: March 24, 2009, 04:57:42 PM »
the area I'm talking about is just below the steering wheel.

3
Restoration / Re: steering column
« on: March 22, 2009, 04:35:57 PM »

Sorry Dave69x33, meant to address this reply to you.

RevDan49

4
Restoration / Re: steering column
« on: March 22, 2009, 04:34:09 PM »

69Z28-RS,

I do appreciate your reply and pictures. I got three pictures, one showing the two columns side by side, one showing the base and coupler. and one showing the middle of the column. I really need a picture of the key area of an original steering column, showing the raised word "lock" and its relationship to the key itself.
By the way, do you still have the old tilt column ?

RevDan49

5
Restoration / Re: steering column
« on: March 21, 2009, 03:14:53 PM »
I was being sarcastic, no one bothered to answer.

6
Restoration / steering column
« on: March 20, 2009, 12:05:17 AM »
just wanted to thank all of you who responded to my request for a simple picture of an existing 1969 Z-28 tilt steering column.

7
Restoration / steering column
« on: March 18, 2009, 06:13:47 PM »
HELP !!!
Need a picture showing the key area and the word "lock" on an original 1969 Z-28 with tilt column.

Thanks

8
General Discussion / correct steering column bowl
« on: March 17, 2009, 05:06:16 PM »
Howdy,

Can anybody e-mail me a picture of the correct version of the word "lock" on a "69 Z-28 tilt steering column bowl. The non-tilt I have now has the word "lock" on a raised boss, with the word actually pointing at the key lock, rather than being printed along side. The raised boss has a pointed end at the key lock, and a squared off opposite end.

Thanks,
Dan

9
Restoration / steering column
« on: March 09, 2009, 06:10:15 PM »
Looking for upper bowl for a floor shift tilt column, the one with the key and turn signal handle, for a 1969 Camaro Z-28 resto project. Has to have the correct "lock"  embossing. Lock embossing is similar to an arrow, pointing at the key cyuinder.

Thanks,
Dan

10
General Discussion / Re: spark plug wires
« on: January 08, 2009, 08:04:14 PM »
Thanks for the replies and pictures.

11
General Discussion / spark plug wires
« on: January 07, 2009, 10:03:20 PM »

Not sure on the correct way to run the spark plug wires on my 1969 Z-28. Any help or pictures?
Seen many variations, I'm sure there is only one correct way.

Thanks

12
General Discussion / Re: 69 z-28 strioes
« on: December 28, 2008, 05:49:24 PM »
Thank You for the replies. Have a ggod New Year!

13
General Discussion / 69 z-28 strioes
« on: December 25, 2008, 09:48:08 PM »
on a 1969 Z-28, on the trunk lid, should the striping go under the "Camaro by Chevrolet" insignia, or around it? I've seen it both ways. In the "Origional Camaro 1967-1969" book, it shows that the stripe should go around the insignia, so the insignia is totally on the body color.

Dan

14
General Discussion / Re: 1969 glass
« on: December 18, 2008, 10:00:44 PM »
thanks for the info. is it possible to get new correct coded windshields?

15
General Discussion / 1969 glass
« on: December 17, 2008, 10:46:56 PM »
Just wondering what the correct etching should be on original glass. My 1969 Z-28 has on the windshield, Safe-Ray Safe-Lite Laminated. The other 5 glasses have Safe-Plate Tempered.
Original, or not?

Thanks

Pages: [1] 2