Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - hgger69

Pages: [1] 2 3 ... 27
1
Mild Modifications / Re: The Hugger goes ZL-1....
« on: June 24, 2018, 08:32:32 PM »
Ok, you got me, lol! Re-read the thread and saw your flexplate.
Haha, good work re-reading everything! :)

2
Mild Modifications / Re: The Hugger goes ZL-1....
« on: June 22, 2018, 06:31:22 AM »
The adds I have seen for PD or DUI said they will take car weight,cam and ect. and curve the dizzy before shipment. I can do it but it would nice to open the box and the paper says total advance, total in at what RPM, ect while getting a good unit at a fair price. If I had a SUN machine I would do it but leaning over a hot motor playing with springs and weights kind of gets old.
Great to hear, Kelley!
Iíll get one from PD, thatís for sure!  8)

3
Mild Modifications / Re: The Hugger goes ZL-1....
« on: June 22, 2018, 06:29:26 AM »
Nothing to consider, right way to do it ;) Any reputable carb builder is gonna ask for cam specs,gears,weight of car,etc... I will say I have heard nothing but good about the Holley HP line.  One of my friends was telling me they were making great numbers with one on the dyno..right out of the box. Slightly lower then the custom carb,which by the way is a great piece. AND the Holley is a couple hundred dollars less.

Another old friend, who is into big cube SBC's in Cobras, has been running the distributer you have pictured for years. Good unit, supports an 800 hp small block with around 7800 shift points with no issues. I was going to ramble on about setting your curve, when you want it "all in", but John Z's article does a much better job! none the less, this will be based on your cam specs. ALSO, Transmission Specialties out of Aston,PA builds bullet proof convertors. Accurate stall. Once again based on your car and engine specs.Get a SFI rated flex plate! If you currently just have a stock one.

Bty, I'm in the camp that loves your engine bay, great job.
Thanks for all that interesting info, I may look into thatís as well. But my intention is to keep the engine close to original so weíll see... :P
Great to hear about he distributor also and your tip regarding the converter, thatís the next step maybe....and I do have a SFI rated flexplate from SCAT! Havenít you read the whole thread?  ;D

...and many thanks for you loving the engine bay, that motivates me to keep up the work! ;)

4
Mild Modifications / Re: The Hugger goes ZL-1....
« on: June 21, 2018, 05:40:32 AM »
I have never had one but my next one will be from them. I understand you can give them your cars specs and they will curve it for the performance
You want. And the price is reasonable.
Thanks for your answer Kelley, thatís even better then I thought!  ;D
You mean the engine specs like cam card, compression, volume etc?
Interesting cause thatís exactly what Iím considering to to with a new custom built carb based on the original Holley 850!

5
Mild Modifications / Re: The Hugger goes ZL-1....
« on: June 16, 2018, 09:26:25 PM »
BTW does anybody have any experience of the distributor from Performance Distributors? It seems to work really well..  ;)

6
Mild Modifications / Re: The Hugger goes ZL-1....
« on: June 16, 2018, 09:17:51 PM »
What rpm is your converter dragging it down to? If it is 600 to 700 see if the engine will run that low in neutral. My stock converter in my Chevelle took the LS6 cam down to 600 or so and it would barely run. My CX converterin my camaro comes down to 700 or so and the L78 will idle there.
I have idle at 1000 and it drags down to like 800. It work ok when the engine has normal running temperatur.

You can try messing with the idle speed, but may need a different torque converter.

Had a really wild 406 small block one time that was a bear to deal with when it had a stock converter, so an aftermarket converter was installed.

What converter is in the car now?
I've changed the main nozzles two steps larger and will try tomorrow again.

I really don't know the what converter that's in it right now, it came with the car but itīs not stock. I was told it was a low stall speed converter. I painted it silver cause it was rather odd looking but here it is:

7
Mild Modifications / Re: The Hugger goes ZL-1....
« on: June 15, 2018, 08:22:54 PM »
Itīs been a while but here are the latest update for the ZL-1 and The Hugger! Itīs been a real struggle just to get the motor up and running again... :(

The first goal was to get the car through the Swedish Vehicle Inspection. Itīs a new rule this year and that's that a car from 1969 or older doesn't have to be checked upon any more if it passes this years test..

Our problem was that the ZL-1 wouldn't run after it had been put back in the Hugger. Despite the new HEI-FlameThrower from PerTronix the engine wouldn't run other on the acc pump. Finally my friend and experienced drag racer P-A sugested that we would check for air leaks and then we found a problem! When we ran the engine on the dyno I had a distance block between the carb and intake and I had to remove that when installing the engine in the Camaro. Instead I had bought a FelPro gasket with rivets round the holes but when the carb was torqued the rivets prevented the gasket to compress and seal the space and we got an air leak!   
A new standard gasket was mounted and the engine started directly! ;)

With that problem solved and quick adjustment of ignition and idle I went to the Inspection and hoped for the best..


Maybe you can't read Swedish but the next inspection time is schedules to 31/12 2099!  ;D
You can also notice a rather low CO-level and that's been adjusted after the visit.

With that inspection behind us its easier to concentrate to get the engine to run better. We realized that the PerTronix HEI doesn't work that well with this ZL-1 so P-A lended me his mechanical HEI from his 1969 Chevelle and then the ZL-1 started to roar!  8)


This is how the engine bay looks today and I couldnthelp myself with that decal, It will please someone and make others angry!  ::)




The problem I have right now is that the engine stops when I put it in D or R gear and the engine is cold... :(
Maybe I have to build myself a correct carb adapted to this ZL-1 and cam or maybe even look at the converter? I will spend this summer testing and then evaluate the next step.

Maybe I get back here with some videos cause the ZL-1 is really moving the Hugger in a really scary way I can tell you...specially when reed a little, holy macaroni!  :P

8
Mild Modifications / Re: The Hugger goes ZL-1....
« on: May 20, 2018, 05:00:36 PM »
very cool. I hope many other pics held hostage are freed. Since they are now showing, can you copy and save them differently so photo bucket doesn't have control over your pics?
It is!  ;)
You can always download them to your own computer,  it I havenít tried yet,


Finally photobucket.com has reached point of no return and now all my former pictures held as hostage are back! The new annual price is fare and immediately after paying all the pics in my threads worldwide are back!   ;D

What is the cost? About $25 per year?
Itís $20 annually.

9
Mild Modifications / Re: The Hugger goes ZL-1....
« on: May 20, 2018, 07:24:20 AM »
Finally photobucket.com has reached point of no return and now all my former pictures held as hostage are back! The new annual price is fare and immediately after paying all the pics in my threads worldwide are back!   ;D

10
Mild Modifications / Re: The Hugger goes ZL-1....
« on: April 28, 2018, 06:06:11 AM »
So have you driven it yet?
Thanks for asking Kelley, but no.  ::)
Iíve  been busy with vacation on the French Riviera, skiing and other stuff so I havenít even started it yet with the new ignition. Hopefully I get more time during May!  ;)

11
Mild Modifications / Re: The Hugger goes ZL-1....
« on: April 09, 2018, 05:45:35 AM »
keep up the progress! When will it hit the road?

(BTW I think only the early cars had the GM logo on the heater hose, most other cars had the ribbed hoses. *Also -They make a better repo of that GM hose)
Thanks!
It might be the fact but these were the ones I found when I was searching around.... :-[ they will do the job I guess, and they look great! ;)

12
Mild Modifications / Re: The Hugger goes ZL-1....
« on: April 08, 2018, 09:04:15 PM »
Yuup, been a while but I'm back with a small update!  ;)

One of the ignition cable retainer broke during the dyno-test so I ordered a new complete kit from HBC. It came in an envelope so it just took a week to get here from USA, impressive! It wasn't until I read the AIM i realized they were a total of 6 retainers...


Mounted:




Lower radiator hose with clamps:


Finally mounted the heater box hoses. Many thanks for the guiding from this forum!




Also the PCV-hose got the right clamp:


...and today the battery and new cables were mounted:


Iīll be back asap when something new happens to the Hugger! Thanks for stopping by! :)

13
Originality / Re: Big block heater hose question!
« on: April 06, 2018, 08:32:20 PM »
Haken, I remember that picture of your pump to intake hose being a little deformed. Mine is too now. I could not find a formed hose except the 90 degree one.
Kelley, itís not deformed att all but there no molded hose for this application, just a normal hose thatís slightly bent to connect the pump and manifold! ;)

14
Originality / Re: Big block heater hose question!
« on: April 06, 2018, 01:03:18 PM »
I looked at my 67 L35 and the water pump hose attaches to the top pipe on the heater box and intake manifold to the bottom pipe. This matches the 67 AIM.
Being the heater box has two different size pipes and the engine has two different size nipples, just match the two.

Mike
The heater core does have two different sizes on the tubing but I donīt think there are two different sizes of the nipples on a 69 BBC but while I built my engine myself I could be wrong!  :P
The picture in my first post is from the 1969 ASM, or AIM, and apparently itīs wrong then!  ::)
Many thanks for your help in this matter, guys! :)

15
Originality / Re: Big block heater hose question!
« on: April 06, 2018, 12:59:37 PM »
Not the first time the assembly manual was wrong.



Great picture, thanks! :)

Pages: [1] 2 3 ... 27