Messages

1

General Discussion / Re: triple xxx show

« on: July 10, 2013, 05:23:24 AM »

Yes PNWCC does host that event, here is the link to their site, looks like it is finally updated their website, and it looks nice:
http://www.pnwcc.com/

2

Decoding/Numbers / Re: Rally Wheel Codes

« on: July 05, 2013, 04:25:45 PM »

I have K1 87 11 YJ

3

General Discussion / Re: triple xxx show

« on: July 01, 2013, 11:30:11 PM »

Lemay's is amazing, I highly recommend going. I have never been to Griot's

4

General Discussion / Re: triple xxx show

« on: April 12, 2013, 04:14:20 AM »

Yes, I try to go at leat once a year, nice venue, always a good turnout

5

General Discussion / Re: triple xxx show

« on: March 17, 2013, 01:51:53 AM »

Was this the show in WA?

6

Originality / Re: Original 1969 SS 396 325HP AUTO no air cond

« on: February 29, 2012, 06:54:52 AM »

396/325 AT
Carb 7029204 FF

7

Originality / Re: '69 Space Saver Spare

« on: September 05, 2011, 08:01:53 PM »

My space saver has 2 valves? I will take pictures and send w/ inflator if desired

8

Restoration / Re: 69 SS hood ornament gasket

« on: June 22, 2011, 06:11:45 PM »

Thanks, I had looked at this as well, this is helpful for me.

I have 2 LH HO...odd.

I think what I am experiencing is the gasket is sitting on the outer edge of the studs and when water gets on top of the HO in the "stack openings", it runs down to outer edge toward the studs and through the stud hole opening of the hood and thus leaks water in the engine compartment.

I may place gasket around those studs, basically surrounding them.

Thanks

9

Restoration / Re: 69 SS hood ornament gasket

« on: June 22, 2011, 05:17:46 PM »

I have the little gasket adhered on the underside of the chrome...the wire mess was overlapping the gasket so I trimmed mesh screent back to sit inside the gasket...the black plate sits on top of hood metal to metal. Then the mesh and chrome pieces. The drain holes are both on the left side of these chrome ornaments, do I have 2 left hand pieces? My aftermarket hood has a few areas for the water to go...on right side (passenger) the drain hole is in a location, I cannot put the drain plug in, no room.

The water is to go into drain hole and run down underside of hood in trough and drop out near radiator I assume.

My gasket is on the outside of my nuts, I thinkit needs to be on the inside to not allow water to get to them, or on both sides, etc..

I have a new underhood pad, yet cannot install until this is resolved.
Thanks

10

Maintenance / Re: Console gauges problems

« on: June 19, 2011, 06:04:55 PM »

My oil pressure gauge buries the needle to over 80lb after started...any ideas where to start looking? This is recent, had no issue before.
Thanks

11

Restoration / Re: Quadrajet Restoration

« on: June 01, 2011, 09:52:35 PM »

These guys in Kirkland WA did me right on my original Quadrajet. Great resource for me on anything related to my carbs.
http://www.carbconn.com/index.php

12

Originality / 1969 Deck Lid Emblem

« on: June 01, 2011, 04:27:50 PM »

I noticed some 1969 have an emblem on the deck lid, while some do not. I currently do not and am also seeing it in assembly manual yet it does not specify if it was standard. I have the rear spoiler. Saw a few strings where this was mentioned, yet could not find my answer.
Thanks

13

Decoding/Numbers / Re: Cowl Tag Looks Odd?

« on: February 16, 2011, 09:19:37 PM »

Kurt, any information you have would be great, as I have limited stuff that came w/ the car when I bought it.
Thanks

14

Restoration / 69 SS hood ornament gasket

« on: July 23, 2010, 06:03:35 PM »

My hood is leaking and assume I have no, or need to replace the gasket at the SS hood ornament, as I tightened the little screws ans it is still leaking. Does anyone recomend which one is best to install? The little nuts on the threaded studs look like they can get damaged easily, I suspect take care on removal and install? Can I buy these little nuts as well I suspect.
Thanks

15

Restoration / Re: Underhood Light

« on: July 16, 2010, 02:49:19 PM »

I tested the light, it works when wire to horn relay and ground the mounting plate for light, this is a seperating fuse it seems, never seen one before..