Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - big iron

Pages: [1] 2 3 ... 43
1
Restoration / Re: Power window wiring routing
« on: September 05, 2017, 09:11:29 PM »
Try Fisher Body Manual. My 67 manual shows front power wiring on page 16-4 fig.16-6 and left side coupe on page 16-10 fig.16-17 and right side conv. on page 16-11 fig 16-18.
Bob

2
Looking for measurements for 3916730 mounting plate. I have mounting plate 3954206, but because the hood catch support brace  was redesigned for 69, I need 3916730 mounting for my 67 build.
Bob

3
Originality / Re: 68 Z trans mount
« on: June 12, 2017, 11:49:58 PM »
T400 is 4-1/4 between bolt holes.
Bob

4
Originality / Re: 68 Quarter window u-jamb screws
« on: June 12, 2017, 10:43:57 PM »
AMK 11636 I believe is used for F&R window clips. I plan to use 11636 in this application because the shoulder would make a more secure connection without distorting the U-Jam seal.
Bob

5
Originality / Re: 68 Quarter window u-jamb screws
« on: June 10, 2017, 05:07:27 PM »
AMK B-11626 has that OD but is phosphate.
Bob

6
Originality / Re: 68 L78 Lifter Valley Splash Shield
« on: June 10, 2017, 04:07:23 PM »
Ed,
Sorry for the typo, should have been (so is it an original GM H.D. Part? ).
Thanks for the info.
Bob

7
Originality / Re: 68 Quarter window u-jamb screws
« on: June 10, 2017, 03:44:58 AM »
Mike,
What is the OD of the screw Head?
Bob

8
Originality / Re: 68 L78 Lifter Valley Splash Shield
« on: June 10, 2017, 03:04:08 AM »
I believe the ZL1's had the shield 3931093, so it is an original GM H.D. part.
Bob

9
Do you happen to know what 'Big Iron' Bob's build date is?

Ed

Ed,
Update. I found this old thread and believe I can give closure to it.
I ordered my 68 RS/SS 396 in middle to late June 1968, took delivery in the middle of July. I do not have the build date ( that is another sad story ) but should be around end of June or early July. When I ordered it I was told that I just made the closing date for factory orders.
I believe all 1968 Camaro T400 drive shafts where built with plastic injected ujoints.

Bob

10
Restoration / Re: Original 67 Turn & Haard Flashers
« on: February 25, 2017, 10:08:59 PM »
I think this topic needs to be in Originality!
Bob

11
Restoration / Original 67 Turn & Haard Flashers
« on: February 25, 2017, 02:22:28 AM »
Need information on types of turn and hazard flashers used in both RS and non RS 67's.
I have part #'s from 67 AIM but they do not translate to type numbers and have no idea what the optional flasher # is used for, except maybe for RS.
Example: Tung-Sol 552
                  "     "   323
                  "     "   224
   "          Signal-Stat  175
   "              "     "      145
So if any members with a 67 RS with original flashers would chime in I would greatly appreciate the replies.
Bob

12
Restoration / Re: 67 RS / SS Build
« on: February 25, 2017, 01:25:38 AM »
Could you tell me what type flashers you have in your 67's ( fuse box- 4 way & to right of steering col. - turn)?
Bob

13
General Discussion / Re: JohnZ, say it ain't so?
« on: February 24, 2017, 06:03:29 PM »
Persevere!

14
General Discussion / Re: JohnZ, say it ain't so?
« on: February 21, 2017, 06:51:55 PM »
Does anyone know anything about John's recovery?
Bob

15
Decoding/Numbers / Hazard and Directional Flasher Date Code
« on: February 20, 2017, 08:59:34 PM »
How do you read date on flashers?
Tung Sol flashers have 3 numbers. Example 1 8 2
Signal Stat flashers have a letter and 3 numbers. Example S 376
Trying to do some research on correct flashers for 67 but there is more confusion than fact and very little fact.
Bob

Pages: [1] 2 3 ... 43