Messages

1

Maintenance / Re: wiper cct diagram

« on: June 06, 2007, 03:31:49 AM »

Thanks Mark
                 Awsome 

Peter

2

Maintenance / Re: wiper cct diagram

« on: June 06, 2007, 12:05:37 AM »

Thanks mrdetails, regret nothing there on benching testing. the main info I need is which pins to apply 12 volts to check operation.

3

Maintenance / Re: wiper cct diagram

« on: June 04, 2007, 12:20:19 AM »

HELP, AM DESPARATE 

4

Maintenance / Re: wiper cct diagram

« on: June 01, 2007, 04:15:02 AM »

Thanks for the reply. I guess what I want is take the wiper motor off the firewall and test it. And by process of elimination find the  problem.
I understand the stand alone pin is 12 V + and the other 2 work ( light blue and dark blue ) work by earthing. I dont wont risk the motor without prior knowledge though 
New 69 wiper motors are not exactly thick on the ground in Australia 

5

Maintenance / wiper cct diagram

« on: June 01, 2007, 12:30:41 AM »

Can any one post a circiut diagram or instructions to bench test a 69 Wiper motor ? I have the "in car" test diagram ang "no go". Now would like to test isolated from the dash switch and car.
 I want to prove the thing works by itself  and prove the problem is then the wiring in the car. Have already replaced the dash switch
Driving me mad trying to get the wipers going 

Thanks in advance

6

General Discussion / Re: Wiper motor wiring

« on: May 17, 2007, 10:26:49 PM »

Thanks for the help guys, will have another go this weekend

7

General Discussion / Wiper motor wiring

« on: May 16, 2007, 11:41:33 PM »

Could someone please post a photo of a 69 wiper motor on the firewall showing the wiring colours. I have had the motor checked - ok.  Replaced the dash switch, but still wont work  The original sockets have gone so have put individual terminals on the light blue/dark blue wire and yellow but no joy. Earth is ok according to a ohmeter, as is the earth on the dashswitch.
Is the yellow wire the only source of 12volts for the wiper motor ?? Note I am not using the washer section,just the wiper
Appeciate any assistance as is driving me mad 

8

General Discussion / Brake Bleeder size ?

« on: April 23, 2007, 01:50:57 AM »

Can anyone tell me the size of the brake bleeders for a 69 Camaro ? Looks like 5/16 or 1/4 ? Need to know before buying the tool. Offset ring spanner.
Both front bleeders are stuck firm and the edges rounded.
Clues in removing ?

9

Decoding/Numbers / Gearbox indentication

« on: April 09, 2007, 11:46:56 PM »

Can any body tell what gearbox this is  marked 3885010, patent and GM branding. Has a aluminium case and is 4 speed.

10

General Discussion / Muncie capability

« on: March 29, 2007, 11:33:40 PM »

Can anyone tell me the power and torque abilities of the M21 and M22  Would either handle a big block ?

11

General Discussion / Re: Gas Pedal Spring

« on: March 19, 2007, 09:33:20 PM »

Fixed ! Thanks a lot guys

12

General Discussion / Re: Gas Pedal Spring

« on: March 19, 2007, 04:17:30 AM »

68Z thanks for the reply. What is AIM? Not up with it in Australia 

13

General Discussion / Gas Pedal Spring

« on: March 18, 2007, 09:44:39 PM »

Can anyone tell how the Gas Pedal spring fits? Had to replace the Gas Pedal and have to replace the spring which broke on removal. Not sure how it goes and would appeciate a sketch or explanation. Sounds dumb but I cant seem to make the replacement spring fit. I have the pedal, spring and pin seperated 

14

Mild Modifications / zz502 into 69

« on: February 26, 2007, 04:41:16 AM »

Anyone done this transplant? Does the 502 sump fit and is there any other clearance problems when fitting to 69. Also are there any headers that will fit without adjustment ? Are the smallblock engine mounts ok ?
Thanks in advance
 

15

General Discussion / Re: New Owner

« on: February 22, 2007, 03:42:12 AM »

Ed,
    The only RH are individual conversions and most are pretty rough. But we can keep LH for historic/ classic cars over a certain age.
My vin is 123379n529462. Can you tell me anything from this ??
Regrards