Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - lynnbilodeau

Pages: [1] 2 3 ... 22
General Discussion / Re: Radiator shroud clip
« on: May 24, 2018, 11:39:18 PM »
"He thought I had mixed up priorities"
Obviously not a car guy.  Probably drives a Prius.

1969 - Orphans / Re: 9N686793 Muncie case on eBay
« on: January 07, 2018, 04:29:47 PM »
Ad says Nov. 69.  P9K is July, 69.

Agree with Kurt (and only saying because you asked for opinions).

If it were the ORIGINAL paint there might be a good argument for keeping it as is.   Even then, given the amount of surfacr rust, a good paint job might be in order.   Being that it is a repaint, the decision toward a good paint job is even easier.  It will preserve it much better.  JMHO, but it is moving fast beyond "patina".

General Discussion / Re: Here we go again! 68 Z/28 buyer beware
« on: August 31, 2017, 01:01:36 AM »
WTH happened to that trim tag, other than having been removed from the car.  I know 68 tags don't give much info, and rarely get faked, but that edges have been cut off that one with shears (at least that is what it looks like) and it has definitely been off the firewall.   Aftermarket rivet (the one you can see) and not installed correctly.

General Discussion / Re: Slick size?
« on: August 19, 2017, 02:50:08 AM »
Yes, if you are using the "newer" sizing, 255 60 15 is probably it for a 69.  I had a KILLER pair of 275 60 15 Hoosiers, and they were so close to rubbing with the car sitting still, I knew they would rub as soon as I started driving it.  Broke my heart to sell them.
I have 255 60 15 on the back right now, and there are no rubbing issues.   Your stock rally wheel should work fine with that size.  255 means it is just over 10 inches wide at teh section width, not tread width.   So a 9 inch wide slick has about a 10 inch section width.   As for heighth, the 255 60 15 is 27 inches tall.  If you can find a slick in the size stated above, 28 x 9, you should still be ok.  27 x 9 would also work.

General Discussion / Re: Yenko Camaro
« on: August 18, 2017, 02:07:11 AM »
Boy, am I out of the loop.  Had no idea Lynn Yenko had been convicted of embezzling.  Sad.

Originality / Re: Fuel Pump Plate finish
« on: July 30, 2017, 02:41:33 AM »
That's ok. He can take better care of it than I can.
That's ok. He can take better care of it than I can.

It is a kind of badge of honor in a sick twisted way, to be called one of Charley's "idiot" friends.  I have alway taken it to mean it is a true "car guy".

I have a little running joke with my four year old twin grandsons.  I ask if their daddy is a "knucklehead" and they always say "yes".  Then I ask if their Pepe' (someone who shall remain me) is a knucklehead, and they always always say "yes".   We consider it a badge of honor to be considered a knuckleheads by the "scooters" (my nickname for the twins) in the same way that an "idiot friend" is a bit of a badge of honor coming from Charley.

Restoration / Re: 1969 Z28 spare wheel
« on: July 29, 2017, 01:28:31 PM »
Something like this.

Originality / Re: Fuel Pump Plate finish
« on: July 29, 2017, 01:18:28 PM »
Quote:  "My old 1100 mile Van Nuys 70 Z28 has a black plate."

You sold it??????

Originality / Re: Holley 4346 vs 4053 base plates
« on: July 01, 2017, 02:48:23 AM »
I would send Eric (vintagemusclecar) a message over on the Yenko site.

General Discussion / Re: I'm pretty sure this is illegal.
« on: March 30, 2017, 12:15:06 PM »
This Ad wasn't an attempt to repair or replace a specific car's body using the original VIN, this isn't an example of bringing a specific VIN back to life by rebodying it.

This is after-the-fact request for a VIN and title. "Need vin and title for 1969 Camaro"

I can see having a specfic VIN and attempting to rebuild that camaro, even when everything needs to be replaced. But this is the reverse of that situation. I agree and understand the first, I don't agree with the this.

You are correct.   Selling a title and vin plate from a destroyed car is illegal.

The other scenarios vary by state.  You can build a dynacorn bodied car in Oklahoma, but it gets a state issued vin.

Originality / Re: Identifying 3961398 Oil Pan, 1969 302 Production line?
« on: February 20, 2017, 02:48:06 AM »
Here you go Bryan.  At least some info.  Can't help with PN.

I have seen no REAL assembly line Z/28 oil pans on ebay in a while.  I see MANY of the "NOS" pans that were still available for $90 from Scoggin Dickey up until just a few years ago.

I have two assembly line pans here.   I will look for date codes, but don't remember seeing one on a pan.  Have one that needs cleaned, so maybe I can look tomorrow.

Originality / Re: Service Engines (CE coded)
« on: February 01, 2017, 01:37:32 AM »
Block is cast Feb 11, 1970.   3970010 Flint block.

Originality / Re: 69 Z Water Pump Pulley
« on: November 04, 2016, 09:48:02 PM »
Could be all of the above.   Just know the repop set I  had for an extra 302 were all crap.  Perhaps there is a different supplier now.

Originality / Re: 69 lower control rubber stops yellow paint
« on: November 02, 2016, 01:41:59 PM »
I would agree.  I believe the ones I posted are NOS over the counter, but the ones on Gary's car are assembly line correct originals.

Pages: [1] 2 3 ... 22