Messages

1

Originality / Re: Rally Wheel Trim Ring Identification Help

« on: January 30, 2021, 07:05:38 PM »

Any additional help with this would be greatly appreciated!!

2

General Discussion / Re: Rally Wheel Trim Ring Identification Help

« on: January 26, 2021, 02:27:33 PM »

Any assistance would be greatly appreciated!!!

3

General Discussion / Rally Wheel Trim Ring Identification Help

« on: January 21, 2021, 02:39:29 PM »

Would anyone be able to help me identify what vehicle the attached Rally Wheel Trim Ring is from?  I have a set that are 14" and 2 1/4" tall, and have an elliptical valve stem opening instead of oval.

I greatly appreciate any help you can provide.

4

Originality / Re: Rally Wheel Trim Ring Identification Help

« on: January 20, 2021, 04:34:30 PM »

Thanks, I researched that and can't seem to find the car these rings came on.  Hopefully someone can help.

5

Originality / Rally Wheel Trim Ring Identification Help

« on: January 17, 2021, 09:09:26 PM »

Would anyone be able to help me identify what vehicle the attached Rally Wheel Trim Ring is from?  I have a set that are 14" and 2 1/4" tall, and have an elliptical valve stem opening instead of oval. 

I greatly appreciate any help you can provide.

6

Originality / Re: Air Cleaner Housing ID Help

« on: May 17, 2020, 01:10:25 AM »

Thank you so much for the information, it is truly helpful!!

7

Originality / Re: Air Cleaner Housing ID Help

« on: May 16, 2020, 03:42:49 AM »

Unfortunately, I couldn't find any numbers on the tag or anywhere else on the housing.  But thanks for mentioning it.

8

Originality / Air Cleaner Housing ID Help

« on: May 15, 2020, 08:37:15 PM »

I would appreciate help identifying the specific applications for the air cleaner housing in the attached pictures.  It is obviously off a 327/250 HP, but is it considered factory for a 1967 & 1968?  And is there other information I should know about it before I attempt to sell it on Ebay?  Also, any assistance on its value would be very helpful.

Thank you for any help you can give me!!

9

Originality / Re: 1968 SS Trunk Lid Badge with Spoiler??

« on: October 21, 2019, 12:20:10 AM »

We are familiar with the templates, but I think my restoration guy is very apprehensive about using them as he did with the 396 badge and they ended up being wrong (I understand it might not have been the template's issue).

10

Originality / Re: 1968 SS Trunk Lid Badge with Spoiler??

« on: October 18, 2019, 04:02:28 AM »

Thanks, I'm restoring the car assuming the spoiler came from the factory. Do you happen to know the specific distance from the trunk lid edges to the emblem?

11

Originality / 1968 SS Trunk Lid Badge with Spoiler??

« on: October 18, 2019, 03:24:01 AM »

Is there a badge on a 1968 SS trunk lid when it has a spoiler?

12

Originality / Re: 1968 SS 396 Correct Badge Location?

« on: October 09, 2019, 05:52:40 PM »

Thank you!!!  I will send these pictures to my restoration guy.

13

Originality / Re: 1968 SS 396 Correct Badge Location?

« on: October 08, 2019, 04:17:38 PM »

My restoration guy is ready to put these badges back on, but I was hoping someone would be able to get me the distance to the badge from the bottom and front of the stripe.  He tried this with a template, but they were not located correctly, so I thought locating off the stripe would be best at this time.

Thank you for any help you can give me!!

14

Originality / Re: 1968 SS 396 Correct Badge Location?

« on: October 07, 2019, 01:00:49 AM »

I would greatly appreciate if someone would be able to provide me with the distance to the badge from the bottom and front of the stripe.

Thank you!!

15

Originality / Re: 1968 SS 396 Correct Badge Location?

« on: October 02, 2019, 08:06:38 PM »

Here are a closer, straight on pictures of the badges on both sides.  They are consistent on each side.