Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - 67conv6cyl

Pages: [1] 2 3
1
General Discussion / Part #3895264
« on: May 09, 2019, 10:41:48 PM »
Would anybody happen to have a picture that they can post of part number 3895264,
Itís a back up switch rod for a Saginaw floor mounted 3 speed.

2
General Discussion / Saginaw back up switch bracket
« on: April 28, 2019, 03:17:22 PM »
I canít seem to find part #3897317 anywhere I have been searching for awhile, itís a bracket that holds the back up switch on 67 & 68 with Saginaw 3 or 4 speed manual transmissions. (Not the same as Muncie bracket).
Does anybody know if there is a part number that superseded this one?

3
Does anybody know how long an original  J-hook spare tire hold down for a convertible is? part# 3841841

4
General Discussion / Standard 3 speed Saginaw
« on: March 27, 2019, 08:56:05 PM »
Does anybody know what a standard Saginaw 3 speed floor mounted shifter factory back up switch looks like?....not the HD trans

5
General Discussion / Original mono spring
« on: April 12, 2018, 01:38:19 PM »
Has anybody here ever re-bent a mono spring?
I have reproduction monoís on the car as of now and the ride hight is perfect......however I would like to put my originals back on because they look factory and I want only original GM parts on this car.  My plan is to have this car being judged at the highest level.

Fortunately I started buying parts 26 years ago and the car had most of its original parts when I bought it.

6
General Discussion / Rear bumper bracket rivet
« on: April 08, 2018, 05:37:59 PM »
I have the original rear bumper it was rechromed. Hartbeet amoung others sell the rivets to attach the center bracket back on.....does anybody know how it install the factory style rivets?

7
General Discussion / Original GM part?
« on: March 23, 2018, 11:14:36 PM »
I have seen this exact fuel cap on many 67 & 68 Camaroís, even in vintage photos of cars when they were new. Is this fuel cap a GM part?

8
1967 - Orphans / 123677N251150
« on: March 12, 2018, 05:30:02 PM »
123677251150 protecto-plate warranty book has survived.

9
General Discussion / Camaroís going over seas?
« on: March 10, 2018, 01:21:38 PM »
I have notice when I go to a car show anywhere in the USA there are less and less first gen Camaroís ever year.

However go to one in England, Germany, or Australia and they are popping up everywhere. I am just wondering why.....the ones I have seen that are in other countries are still left hand drive with regular trim tags. Any clues on what is causing the shift?

10
General Discussion / 67 Camaro with four bolt door hinge?
« on: March 05, 2018, 04:11:32 PM »
Did any late 67ís have door hinges like the 68ís had (4 bolts instead of 3 mounting to the hinge pillar on car)?

11
General Discussion / 67 GM tow hitch
« on: January 19, 2018, 01:22:27 AM »
Would anybody know the part number for the GM accessory tow hitch for a 67 Camaro?

12
General Discussion / 14x5 steel rims
« on: August 24, 2017, 01:05:32 PM »
Would anybody know if all early non SS or Z28 cars in 67 left the factory with 14x5 steel rims or what date did they switch to 14x6 rims? I am trying to go completely factory in every detail and I bought car 26 years ago and it had 14x6 steel rims on it, however acrroding to my research they should be 14x5 rims (car is 04A 67 build date).

13
General Discussion / Heater core seals
« on: August 19, 2017, 04:40:47 PM »
Does anybody have an opinion on what are the best heater core gaskets on the market today for a small block heater core?

14
6-cylinder Camaros / Thermostat housing for 6 cyl
« on: August 03, 2017, 10:27:43 PM »
Can anybody tell what the original correct part number for a 6 cyl thermostat housing is?

15
General Discussion / Car in Iowa
« on: July 21, 2017, 12:13:14 PM »
Are any members near by  Clarence Iowa?
There is a 67 convertible there that I am very interested in and would like to buy if I could find somebody to put there eyes on it. The car appears to be super solid with all original panels. Although it's hard to tell from  the pictures.

Pages: [1] 2 3