Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - hdptsr

Pages: [1]
1
Restoration / Hole in trunk pan for 1969 camaro for fuel sending unit
« on: June 09, 2023, 11:45:19 PM »
Hello,
I had to replace my trunk pan, and am now installing the fuel tank and sender.  I realized I did not take note of where the sending unit comes through the trunk pan.  Does anyone have a picture and measurements where this hole for the tan wire should be drilled.  What is the whole size?  Also where does the ground wire attach?  Thanks for your help. 

2
Originality / 1969 Camaro AC Dryer
« on: April 15, 2023, 04:39:14 AM »
What color was the AC dryer on a 1969 SB Camaro?  Got a re-pop and it is aluminum color.  Is this correct? 

3
Originality / 1969 Power Steering Pump
« on: February 15, 2023, 05:41:36 PM »
Hello,

I have a 1969 Z10 350 with manual transmission, factory AC and Power Steering car.  It was a basket case and am trying to bolt everything back up to the motor.  The PS pump double pulley seems to be to far forward by about 1/4 inch.  I am using factory cradle bracket and support bracket form forward manifold to motor mount.  I know the pulleys are correct.  I bought a remanufactured PS pump Sagnaw style.  My question is the rounded banjo style PS pumps standard on the 1969 SB or the more square topped PS pump?  I have seen both for sale for 1969 SB.  What else could be causing the mis-alignment of pulleys?  The crank pulley is a 3 groove pulley.  Thanks for any help you can provide

4
Mild Modifications / Flowmaster American Thunder System 17104
« on: February 12, 2023, 08:20:55 PM »
Hello,

I Have a factory small block 350 dual exhaust car and wanted to replace the exhaust.  I was considering the Flowmaster American Thunder 17104 system.  Can you use the factory exhaust hangers or do you have to drill through the floorboard and use the hangers they provide.  I would like to really use the factory hangers to make it look as original as possible.  any insight anyone can provide would be great!  Thanks  :)[/b]

5
Originality / 1/4 inch vapor return hose
« on: March 30, 2021, 08:30:48 PM »
What is the length of the short hose that connects the (AC fuel fuel) filter to the metal vapor return line on the 1969 Camaro on 350 SS.  Are the squeeze fuel line clips suppose to be painted red? 

6
Originality / AC Hose
« on: March 07, 2021, 06:10:00 AM »
What is the length of foam on 1969 Camaro AC hose, the hose from compressor to the Evaporator?  The protective foam as it goes over the alternator?  Do they sell a reproduction? 

7
Originality / 1969 Power Booster Intake fitting
« on: March 01, 2021, 04:58:06 PM »
Could you tell me what is the correct fitting for the vacuum port on a 04C 1969 Z10 with 350 L48 engine with Air conditioning, manual transmission and of course RS.  Did this engine use the Vacuum Power brake Pipe?  Or did the hose go directly to the intake fitting?  Did the fitting have 1 or 2 additional vacuum ports other than the threaded one going to the brake power booster?  It is illustrated in the 1969 Camaro assembly manual under J50 A5, but I can not determine which fitting is correct for my car.  Thanks for your help

8
General Discussion / 1969 Z10
« on: June 21, 2012, 06:24:26 AM »
I have a 1969 RS/SS Z10 with AC, 4 speed.  I want to order new front coils but do not know what the original code should be.  Is it HA?

9
General Discussion / Do 1969 camaro steering colunms have numbers?
« on: June 19, 2012, 10:53:29 PM »
I want to buy a 1969 tilt colunm for a muncie floor shift car but have not been able to find any place that lists the numbers for that colunm.  Do they even have numbers?  How do I know I am getting the right colunm?

10
Decoding/Numbers / Steering colunm number for 1969 RS/SS 4 speed Z 10
« on: June 19, 2012, 01:52:32 PM »
I have a build date of 04C.  I am tryoing to find the correct production number tilt steering colunm for my car.  What is the correct production numbers for a four speed with a tilt colunm for a 1969 RS/SS?

11
Restoration / Template for holes in deck lid for 1969 RS/SS Spoiler
« on: September 11, 2011, 03:02:17 PM »
Does anyone have a template for a 1969 RS/SS holes in the deck lid for the spoiler? 

12
Restoration / 1969 RS/SS Reverse light template for lower pan
« on: August 11, 2011, 03:35:53 AM »
I recently had to replace the tail pan on my 1969 Z10 camaro.  I bought the Dynacorn replacement panel and it does not have the reverse light cut outs.  Does any one have a template for this or the easiest way to cut them out and get it right?  Thx Joe

13
Restoration / 1969 SS350 muncie 4 speed tunnel hole template
« on: August 10, 2011, 10:24:02 PM »
I installed a new floor and want to cut the correct hole in the trans tunnel for a muncie 4 speed.  The car is a console small block car.  I would like a template I can follow to cut the hole, rather than trace the shifter boot ect.  What are the factory measurements? There is a template on the fourm but the tranny tunnel tapers and in this template there is no account for this.  Thanks Joe

14
General Discussion / factory 1969 12 bolt pinion angle
« on: December 03, 2010, 07:34:04 AM »
I have a 1969 SS (350 300HP) car with a factory 12 bolt.  The owner prior to me changed the multi leaf perches to mono.  I want to weld multi perches back on however would like to know the correct pinion angle that the spring perches were welded to the axle tubes at the factory.  With the spring perches level what is the correct down angle in degrees of the pinion? (out of the car) Thanks Joe

Pages: [1]