Topics

1

Maintenance / 67 Camaro Standard AC Switch

« on: June 10, 2014, 01:37:25 PM »

I have fixed my blower on the factory air 67 camaro standard.  Does anyone have a picture of the AC switch that kick on when the lever on the four season console is pulled to cold and activates the compressor?  The wiring diagram doesn't help with the physical location. 

2

Mild Modifications / Cowl Induction with A/C

« on: June 17, 2008, 08:59:06 PM »

Has anyone out there tried a cowl induction with A/C in a 67.  I have 67 with factory A/C and am not sure where to connect up the cowl connection.

Mark

3

Mild Modifications / Flaming River Steering column with Hedman Headers

« on: May 15, 2008, 06:52:03 PM »

I am hoping someone out there can help me with a problem I have run into with my Flaming River Steering Column, Hedman Header, and Flaming River Rack.  My driver side Hedman Header is in the way of my Flaming River Rack and Pinion connection and the column by the same company.  I am using a three piece universal joint and the angle of the shafts are more than what is needed for a smooth turning column.  The front pipe of the header comes over the middle two and over the rack and pinion connection. Any one has done the same set up and came up with a way of fitting everything together?



Appreciate any help before I start cutting the header and rewelding.



Mark

4

General Discussion / Hedman Husler Headers and A/C bracket location

« on: March 22, 2008, 05:28:48 PM »

Does someone out there have a diagram or a picture of how the A/C bracket, P/N 20110, fit on the Hedman Husler Hedder and the AC evaporator unit in a 67 SBC Camaro.  I don't want to screw it up and melt the plastic evaporator housing.  Any tips would be greatly appreciated.

Thanks,

Mark

5

Mild Modifications / Hedman Husler Headers and A/C bracket location

« on: March 20, 2008, 10:23:50 PM »

Does someone out there have a diagram or a picture of how the A/C bracket, P/N 20110, fit on the Hedman Husler Hedder and the AC evaporator unit in a 67 SBC Camaro.  I don't want to screw it up and melt the plastic evaporator housing.  Any tips would be greatly appreciated.

Thanks,

Mark

6

General Discussion / 68 center console and shifter for a 67 camaro

« on: March 06, 2008, 04:28:19 PM »

Due to the exorbitant cost of used 67 original shifters and the fact that I like the feel and the look of the Horseshoe shifter on the 68, I have decided to replace my shifter on the tree for my 67 with a 68 horseshoe shifter and console. I will be putting in an after market steering column.  I have heard that the wiring will not match up.  Any insight into how to match the wiring of a 68 console to a 67 harness would be much appreciated. 

Thanks,

Mark

7

Mild Modifications / 68 center console for a 67 camaro

« on: March 04, 2008, 04:29:10 PM »

Hi all,

Due to the exorbitant cost of used 67 original shifters and the fact that I like the feel and the look of the Horseshoe shifter on the 68, I have decided to replace my shifter on the tree for my 67 with a 68 horseshoe shifter and console. I will be putting in an after market steering column.  I have heard that the wiring will not match up.  Any insight into how to match the wiring of a 68 console to a 67 harness would be much appreciated. 

Thanks,

Mark

8

Mild Modifications / 67 Camaro Steering Column Replacement

« on: February 21, 2008, 03:49:22 AM »

I have a few questions on the replacing my stock 67 steering column with an aftermarket one now that I have switch the shifter from the tree to the flloor.  I have a powersteering.

1.  What supplier would you recommend
2. Any issues with fit I should be aware of
3. What other parts will I need to order to make the swap work.

Thanks,

Mark