Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - fsc66

Pages: [1] 2 3 ... 8
1
General Discussion / Re: Any info on Reese Chevrolet in Mechanicsburg, PA?
« on: November 13, 2017, 08:24:54 PM »
Mike,
Sent you a load of ads directly from newspapers.com
Watch your spam.
Paul

2
General Discussion / Re: Original dealer info for 1st gens is available
« on: November 13, 2017, 12:44:47 AM »
PM me what you have and I'll see if I can help

Paul

3
General Discussion / Re: Any info on Reese Chevrolet in Mechanicsburg, PA?
« on: November 13, 2017, 12:43:36 AM »
Mike:
PM me your e-Mail and I'll send you some ads.
Paul

4
General Discussion / Re: Any info on Reese Chevrolet in Mechanicsburg, PA?
« on: November 11, 2017, 09:29:07 PM »
Thousands of ads out there, what are you looking for? Also want year Camaro do you have?

Paul

5
Wow,
Heck of a dealership!!!!!!!!!










Paul

6
General Discussion / Evolution of Camaro
« on: November 06, 2017, 08:56:33 PM »
Someone sent this to me, I'm sorry if it was already posted:

https://www.youtube.com/watch?time_continue=1&v=XA9RRf6RslA

Paul

7
Site Comments/Discussion / Re: 20 Years of CRG
« on: October 17, 2017, 01:36:54 PM »
The site that all others try to emulate!!!!!!!!

Thanks,
Paul

8
General Discussion / Re: Original dealer info for 1st gens is available
« on: September 19, 2017, 04:06:39 AM »
Robert Chevrolet is still there and still in the same family. Owner races cars on the side. I just bought an Equinox there a few months ago for my sis-in-law. There is no paperwork anywhere in that place left over.
The ad below was found behind the sheet rock last renovation.



Paul

9
General Discussion / Re: Bill conner chevrolet inc
« on: September 19, 2017, 12:25:43 AM »
Sent about 12-14 ads, they will show coming from newspapers.com so watch your spam.

Paul

10
General Discussion / Re: Bill conner chevrolet inc
« on: September 18, 2017, 01:12:57 PM »
PM me your e-mail address and I will send you a bunch of ads from Conner for 1968.

Paul Winvoices

11
General Discussion / Re: Original dealer info for 1st gens is available
« on: September 01, 2017, 06:16:42 PM »
I contacted the Belvidere NJ library reference department looking for original listings for J&B.
They sent me the attached, so we know J&B was there in 1970.







Paul

12
General Discussion / Re: Original dealer info for 1st gens is available
« on: September 01, 2017, 02:31:02 PM »
Dealer 35 Zone 166 is: J&B Chevrolet and Oldsmobile, 4 Prospect St, Belvidere, NJ. Prior to J&B the Chevrolet Dealership at this same location was Stewart Chevrolet who had been there since at least the 30's. J&B sold to Riverside Chevrolet who was owned by Ed Rossi who still owns NJ Dealerships. Currently the building is owned and operated by Crossflags Corvettes and Vintage Motorcars. I spoke to Bill the owner and he confirmed J&B being there prior to Riverside. He has already scoured over the building and no records anywhere, just an old safe that still shows Stewart Chevrolet. He has a pic of the building when owned bu Stewart on his web site:
http://www.cvette.com/

Paul Winvoices


13
General Discussion / Re: Looking for a specific car VIN 124379N630100
« on: August 21, 2017, 12:42:03 AM »
E-mail George Zapaora and ask if anyone has sent that VIN in asking for a Vintage Vehicle Report. I'm sure if anyone did he would not give you their name but perhaps he might tell you if anyone has inquired.

http://www.vintagevehicleservices.com
Grorge's e-mail is on the bottom of this page.

Paul

14
Garage Talk / Re: '68 Multi Plex Unit
« on: July 20, 2017, 09:43:20 AM »
On the 1966 Full Size Car, you could have had console stereo Multiplex with either a Caprice or Impala SS. The determining factor was the gauge package. In the Caprice, if you ordered RPO A51 it included bucket seats and gauges along with lower dash pads. In the SS bucket seats were standard so you ordered the D59 gauge package which again included the lower padded dash. The gauges mounted in the same place the standard multiplex would have installed, hence the console mount fo these models with the gauge package.
I am in the process of having the Multiplex Decal reproduced, should be done in a few weeks.
Paul

15
Here's some info:
If you goggle Martin Kovich, Tamaqua PA you'll get some hits to call:

Paul Winvoices

Pages: [1] 2 3 ... 8