Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Northernforce

Pages: [1] 2
1
Decoding/Numbers / Re: Z bar frame bracket stamping
« on: September 24, 2017, 12:20:37 AM »
Thanks Ed-I figured it was a repop as it was powder coated -nice and shiny-paid only $5 .
Keep on Cruising!!!
Dave

2
Decoding/Numbers / Z bar frame bracket stamping
« on: September 23, 2017, 09:48:18 PM »
I picked up a Z bar frame bracket at a local swap meet-it has CHQ stamped on it-is this an original gm piece or a reproduction?Thanks for any input!!!
Keep on cruising!
Dave

3
Garage Talk / Re: Evaporust...WOW !
« on: September 17, 2016, 03:50:30 PM »
I have used Evaporust for years-used to blast my rusty bolts etc-now just soak them overnight in evaporust-after I rinse with water and dry I spray Boeshield T-9 on my parts.
Keep on Cruising!!!
Dave

4
Garage Talk / Re: Keith Chevrolet Circa 1969
« on: June 02, 2016, 12:20:55 AM »
Thanks Paul-I will check it out!
Keep on Cruising!!!!
Dave

5
Garage Talk / Keith Chevrolet Circa 1969
« on: April 27, 2016, 07:02:30 PM »
I was looking at a NOS gm box and noticed a postage stamped from Oakland,CA dated October 31,1969 -I guess Gm mailed parts back then- it was shipped from General Motors Parts Division in Oakland,Ca to a Keith Chevrolet-the res is hard to make out but I think it is Chester,PA or Chester(another state)-I take it this dealership isn't in business or the name has changed-any info would be appreciated!
Keep on Cruising!!!
Dave

6
General Discussion / 1970 Chevrolet Dealer/Sales Album
« on: December 06, 2015, 04:56:02 PM »
I recently picked up a mint 1970 dealer album.It does not have any camaro or corvette info in it due to the strike  I guess as all it reads is information will be added later..It must be one of the early ones put out-just curious when they added the info on the camaro and corvette to this book .Nice reading material.Thanks for any input.
Keep on Cruising!
Dave

7
Originality / Re: Factory motor mounts
« on: November 11, 2015, 02:21:55 PM »
Thanks I had checked that out earlier but it doesn't  mention the numbers for the engine mounts-thanks!
Keep on Cruising!
Dave

8
Originality / Factory motor mounts
« on: November 11, 2015, 02:51:12 AM »
I picked up a box full of camaro parts from a guy-I got a mint set of 3950113/114 69 bb frame mounts and a pair of nos in gm boxes #3990916 engine mounts-1  nos # 6258154 in gm box mount and 2 mint /used #330973 engine mounts-any idea which mounts were installed at the factory? Thanks in advance!
Keep on Cruising!!!
Dave

9
Originality / Re: grooved cowl air cleaner
« on: October 18, 2015, 12:19:51 AM »
I think the only difference from a factory installed one to the over the counter service replacement one is the vent tube shape-factory ones have the 90 degree bend while the service replacement ones have the two 45 degree shape
Keep on Cruising!
Dave

10
Decoding/Numbers / Stewart Warner Gear Reduction
« on: September 13, 2015, 09:10:52 PM »
Cleaning out my toolbox in the garage-found  a Stewart Warner gear/speedo reduction unit has .9743 Y stamped on it-any idea what it is from?Thanks in advance!!!!It may be from a 70 gm pick up-not sure.
Keep on Cruising!!
Dave

11
General Discussion / Re: Stolen Z Found
« on: August 18, 2015, 10:58:25 PM »
My buddy had a nice mid 80's blazer all done up that he drove on nice /dry days in the winter as well as all summer-he and his family were ice skating at a local outdoor rink when he saw his truck being driven away.Hard to chase someone on skates-they found it 3 days later all burnt!
Keep on Cruising!!!

Dave

12
Originality / #20037597 inside window handles with black knobs
« on: August 08, 2015, 06:22:20 PM »
I know most came with clear knobs and are expensive to find NOS  but what would a set of NOS black knob handles fit and be worth? Thanks in advance!
Keep on Cruising!
Dave

13
Originality / Original Cowl Induction Throttle Arm
« on: August 08, 2015, 01:03:44 PM »
Is there any way to tell an original or gm piece from a reproduction-was at a friends house and he had a cowl induction throttle arm-he wasn't sure if it was a reproduction or not-the only stamping I saw was  "C" stamped on it-whats a gm one worth?Thanks in advance!
Keep on Cruising!

Dave

14
Originality / Re: "W" stamped on the cowl induction flange
« on: August 21, 2014, 03:33:27 PM »
Thanks for posting the pictures Bryon-noticed other parts with the "W" stamping on them-I have a holley heat shield that has the W stamping.
Keep on Cruising!!!

Dave

15
Originality / Re: "W" stamped on the cowl induction flange
« on: August 20, 2014, 02:47:32 AM »
I am out of town till Thursday-will post a picture then-thanks!
Keep on Cruising!
Dave

Pages: [1] 2