1
Originality / Option Packages
« on: November 22, 2018, 01:51:07 PM »
Does anyone have any info if there were option packages on first gen Cars back in the day like there is today? or could they be ordered alacarte?
News:
Welcome to the CRG Discussion Forum!
Classified ads are not allowed on the forum.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1] 2
2
Originality / Corvette Bronze 68 Z/28 RS production numbers
« on: November 20, 2018, 03:35:00 AM »
Does anyone know how many of this model were produced?
3
Originality / Re: Brake Booster Valve Tag
« on: February 10, 2017, 04:08:49 PM »I think this requires pictures of the car and why so low of miles??
Bill, This car sat in a concrete block garage in the woods of WV for 42 years, needless to say it had a bit of rust issues and had to go through a complete restoration.
4
Originality / Re: Brake Booster Valve Tag
« on: February 10, 2017, 03:45:39 PM »Thanks. Just curious what are the plans for the original one?
It came apart during dis-assembly.
Attached is a photo of the original, the one I had made and the after market one (right)
5
Originality / Re: Brake Booster Valve Tag
« on: February 10, 2017, 01:18:31 PM »
Tim, I don't know the answer to your question, maybe someone else will pipe in and let us know.
Darrell, this car is a power drum car.
Darrell, this car is a power drum car.
6
Originality / Re: Brake Booster Valve Tag
« on: February 10, 2017, 04:31:00 AM »
I have had the CG tag made by a print shop. I think it looks pretty good.
7
Originality / Re: Muncie Shifter Assembly
« on: December 31, 2016, 02:15:17 PM »
To all
I am restoring a 68 L78 (9977 original miles) and the prior owner had replace the shifter with a Hurst Comp set up. I did receive with the car the original shifter and rods but they had welded broken rods together.
I understand big blocks and small blocks used different rods and I am in need af a set of big block rods.
The part #'s for these rods are
1st & 2nd 3930063
3rd & 4th 3930065
Reverse 3930067
Any help or direction would be greatly appreciated
I am restoring a 68 L78 (9977 original miles) and the prior owner had replace the shifter with a Hurst Comp set up. I did receive with the car the original shifter and rods but they had welded broken rods together.
I understand big blocks and small blocks used different rods and I am in need af a set of big block rods.
The part #'s for these rods are
1st & 2nd 3930063
3rd & 4th 3930065
Reverse 3930067
Any help or direction would be greatly appreciated
8
Originality / Brake Booster Valve Tag
« on: August 03, 2015, 04:02:40 PM »
Need a little help.
I have a 9978 original mile L78 car with a brake booster valve tag CG and I cannot find a replacement. I can only find CH & CU.
Any help locating would be great.
Thanks
I have a 9978 original mile L78 car with a brake booster valve tag CG and I cannot find a replacement. I can only find CH & CU.
Any help locating would be great.
Thanks
9
General Discussion / Re: Frederick Nationals ...
« on: June 26, 2014, 12:39:19 PM »
This was my first trip to the Nationals and I was very impressed with the work everyone has put in these cars. I am restoring a low mileage 68 L78 and will be back to study over the next few years.
Larry (scoop) brought a car that raised my expectations of where I need to take my restoration. Thanks for the great info everyone.
Dan
Larry (scoop) brought a car that raised my expectations of where I need to take my restoration. Thanks for the great info everyone.
Dan
10
Decoding/Numbers / 68 NOR build sheet
« on: September 06, 2013, 03:39:52 PM »
Can someone tell me if a built sheet for this year was every found and where I might look?
It is a NOR built 68 L78 Camaro
Thank you
It is a NOR built 68 L78 Camaro
Thank you
11
Originality / Re: 68 SS L78 Stripes
« on: August 12, 2013, 04:58:14 PM »
OK, Thanks everyone.
I will check tonight as I may have not looked hard enough at the drivers door.
I will check tonight as I may have not looked hard enough at the drivers door.
12
Originality / Re: 68 SS L78 Stripes
« on: August 12, 2013, 03:49:02 PM »Can someone tell me if this the norm or could it have been in any configuration.
1968 SS L78 (Original mileage 9977 & original paint)
D90 stripes configured in the following fashion.
Nose and to the front of the wheel wells is painted.
Drivers side, rear of wheel well to door is a decal and door is painted.
Passenger side, rear of wheel well and door are decals.
Passenger side is correct.
Steve
Thanks, where did you get the info to confirm this and should the drivers side be the same? I will look at it again.
13
Originality / Re: 68 SS L78 Stripes
« on: August 12, 2013, 01:15:30 PM »
DD Z28 is the first initials of me and my wife and our other car is a 69 Z28.
14
Originality / 68 SS L78 Stripes
« on: August 12, 2013, 04:12:01 AM »
Can someone tell me if this the norm or could it have been in any configuration.
1968 SS L78 (Original mileage 9977 & original paint)
D90 stripes configured in the following fashion.
Nose and to the front of the wheel wells is painted.
Drivers side, rear of wheel well to door is a decal and door is painted.
Passenger side, rear of wheel well and door are decals.
1968 SS L78 (Original mileage 9977 & original paint)
D90 stripes configured in the following fashion.
Nose and to the front of the wheel wells is painted.
Drivers side, rear of wheel well to door is a decal and door is painted.
Passenger side, rear of wheel well and door are decals.
15
Originality / Re: 69 Z28 Carb accel linkage and vacuum hardline?
« on: May 08, 2013, 01:45:02 PM »
Here are 2 photos of the steel tubes I purchased and 1 that I made to fit.
Pages: [1] 2