Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - rod396

Pages: [1] 2 3 4
1
Originality / Re: 1969 RS Headlight Bucket Shim
« on: November 22, 2017, 08:14:23 PM »
I was trying to view the photo -?? Can someone direct me on this?
Thanks.

2
Originality / Re: 68 Rear Window Defogger
« on: November 15, 2017, 09:10:19 PM »
Thank you, Ed.

3
Originality / 68 Rear Window Defogger
« on: November 14, 2017, 08:58:25 PM »
On a 68 (sept 67 prod), which would be the correct grille for the rear window defogger? - I have two - one being a rectangle and the other with a curve on one end.

4
Originality / Re: 68 Firebird vs Camaro Dash Grab Bar........
« on: November 07, 2017, 08:59:48 PM »
OK thanks - other than that, are they wider than the Camaro?

5
Originality / 68 Firebird vs Camaro Dash Grab Bar........
« on: November 07, 2017, 03:47:40 PM »
Is the dash grab bar on a 68 Camaro different than that of the same year Firebird? If so, does anybody know what the differences are?

6
Originality / Re: 396 Big Block Water Pump Back Plate, 68
« on: October 30, 2017, 08:28:16 PM »
Thanks for your help! I'll run with the lipped version.

7
Originality / Re: 396 Big Block Water Pump Back Plate, 68
« on: October 24, 2017, 08:30:16 PM »
No one knows the answer to this one?

8
Originality / 396 Big Block Water Pump Back Plate, 68
« on: October 13, 2017, 08:44:56 PM »
I need to confirm the correct water pump rear cover plate for my '68 396 "284" short pump - which is correct:
The flat, plain version, or,
The version with the flared outer lip on it??
I have seen the flat plate on '65-'66 original pumps, but do not know when they changed the rear plate design.
Also, are the 1/4 x 20 attaching bolts 7/16" hex head like the Timing Cover, or are they flat-headed, slotted screw heads?

Any help greatly appreciated.
Thank you.

9
Originality / Re: 68 Core Support - Standard vs RS..............
« on: September 14, 2017, 08:23:00 PM »
Build date 10/67

10
Originality / Re: 68 Core Support - Standard vs RS..............
« on: September 13, 2017, 09:36:17 PM »
Thanks for your responses. Yes, I was questioning this solely on the fact that the holes were pierced, and not stamped.

11
Originality / 68 Core Support - Standard vs RS..............
« on: September 11, 2017, 08:24:14 PM »
On a 68 RS, I do not have the original Core support, but found one from a 68 Standard. My question is, on the washer bottle mount, would the factory original core support on the RS NOT have the 3 triangular pattern holes pierced on the left side of the core support, as the RS mounts the bottle farther back on fender?
Does anybody have an original 68 RS on which they could confirm these holes pierced or not?
Thank you.

12
Originality / Re: Oil sender line for console gauge
« on: September 01, 2017, 08:24:47 PM »
Thanks Ed.

13
Originality / Oil sender line for console gauge
« on: August 30, 2017, 08:17:19 PM »
In 68, with the console gauge package, was the line originally copper or plastic?
Thank you.

14
Originality / Re: 68 Big Block Radiator Codes
« on: June 30, 2017, 08:23:31 PM »
So it is only the tag that is affixed to the tank that specifies the core
The OL only denotes the larger tank itself

15
Originality / 68 Big Block Radiator Codes
« on: June 26, 2017, 02:55:11 PM »
I am of the understanding that the 67-68 Big Block radiator code on the pass side tank for manual trans is "OL", and this is for a 4-row core (?) but I can't seem to find what the code would be for a 23-inch, 3-Row core, Big Block, manual trans.

Does anybody know what the correct code for the pass tank would be? Original/survivor examples.
Thank you.

Pages: [1] 2 3 4