Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Danzo

Pages: [1] 2 3 ... 13
1
Originality / Re: fuel hose
« on: November 12, 2018, 12:55:57 AM »
Anyone?

2
Restoration / Re: Difficulty Disassembling Smog Pump
« on: November 10, 2018, 01:49:11 AM »
Never had to soak one.

3
Restoration / Re: Difficulty Disassembling Smog Pump
« on: November 05, 2018, 01:51:20 AM »
Towards the rear.

4
Originality / Re: fuel hose
« on: November 05, 2018, 01:04:20 AM »
Does anyone currently make this hose?
Thanks, Doc

5
Restoration / Re: Difficulty Disassembling Smog Pump
« on: November 05, 2018, 12:07:43 AM »
Tim, just did mine. Take a punch and knock out the 2 dowels. The back cover should then come apart. If you need any help,let me know.
Doc 

6
Restoration / Re: best gas tank sending unit
« on: October 20, 2018, 10:27:46 PM »
Is it stainless?

7
Restoration / Re: best gas tank sending unit
« on: October 20, 2018, 12:44:46 AM »
Ed listed one he purchased (I think from the car and truck shop?). Is this one stainless? I tried to find the original thread it was in to no avail.
Thanks, Doc.

8
Restoration / best gas tank sending unit
« on: October 10, 2018, 01:36:56 AM »
Who sells the best one for a 69 Z?
Thanks, Doc.

9
General Discussion / Yellow 69 Z
« on: September 26, 2018, 08:38:48 PM »
Guys, does anyone have any info on this car? Friend of mine likes it.
Thanks, Doc.

https://www.mecum.com/lots/DA1018-359840/1969-chevrolet-camaro-rs-z28/

10
Restoration / Re: disc brake wheel hub finish
« on: September 02, 2018, 11:55:14 PM »
I believe you are correct.

11
Restoration / Re: 69 smog pump resto
« on: September 02, 2018, 04:40:18 PM »
All the marks that were there before i started are still there. they are deep enough that you can feel them with your fingernail.

12
Restoration / Re: 69 smog pump resto
« on: September 02, 2018, 02:52:33 PM »
A combination of steel wool and wire wheels. Anyone have any experience with "dulling" aluminum? Read some good and bad posts about oven cleaner. Anyone know what Bill Hodel does to finish his?
Thanks, Doc.

13
Restoration / Re: 69 smog pump resto
« on: September 02, 2018, 12:24:27 AM »
Here what I have after cleaning 49+ years of oxidation, dirt, orange paint. I can clearly see the extrusion marks that Ed pointed out. Do you think it is too shiny or should I just flat clear it and call it done?
Thanks, Doc.

14
Restoration / Re: 69 smog pump resto
« on: August 31, 2018, 11:34:30 PM »
Ed does that pump have some kind of manufacturer/factory"coating"? The machined circles look much brighter than the pump body. What does a "Hodel" pump look like finished?
Thanks, Doc.

15
Restoration / Re: 69 smog pump resto
« on: August 31, 2018, 06:30:59 PM »
Jim, do you have any pictures?
Thanks, Doc.

Pages: [1] 2 3 ... 13