Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 67ss350camaro

Pages: [1] 2 3 ... 11
1
1967 - Orphans / Re: 7L124020 396/375 motor assembled 0301MR
« on: April 06, 2017, 02:36:15 PM »
Even with a Los vin the engine date is built after the cars vin date. Ether you are reading the vin wrong or it has been restamped. It would be nice to see a picture of the pad.

Thanks for the heads up on this Bryon.

2
General Discussion / Re: Do You Still Have Your First Car?
« on: July 03, 2014, 03:53:40 PM »
I still have my first car (my 67) and my other 2 Camaros also, but unofficially the 97 is my oldest son's car now.

3
Decoding/Numbers / Re: 1967 Camaro RS/SS
« on: July 03, 2014, 03:41:41 PM »
I don't see anything wrong with those dates.  RS/SS 4-speed with A/C...Nice!

4
Decoding/Numbers / Re: Decode please. 67 trim tag
« on: July 23, 2013, 06:41:27 PM »
Actually since it is a NOR car, and no console, it could have been a powerglide on the column.  So in this case, the trans could have been a M35 or M15.

5
Decoding/Numbers / Re: 1967 RS
« on: July 23, 2013, 06:36:25 PM »
The N40 was probably just missed on the POP.  The U17 was not coded on the cowl tag or POP, so I bet it was factory also.

6
General Discussion / Re: CRG YouTube Channel
« on: July 19, 2013, 06:21:54 PM »
Well thanks to Chick ( 68camaroz28 ) we now have the Sept 68 and Sept 69 kits on line.  Check them out!

7
Decoding/Numbers / Re: 1967 RS
« on: July 18, 2013, 02:16:20 PM »
I would like to get more info on this car you posted about (124377L114810).  
If you can help, I need a picture of the cowl tag, POP and where the speedometer cable comes through the firewall.

The car should not have the 4P on the cowl tag, it is a little to early for that.

8
General Discussion / Re: CRG YouTube Channel
« on: June 08, 2013, 06:14:18 PM »
Send me an email: dakcoffman@gmail.com
Thanks for your willingness to help.

9
General Discussion / Re: CRG YouTube Channel
« on: June 07, 2013, 07:40:33 PM »
Thanks to Brett Willis, we now have the complete Camaro video up on CRG's YouTube Channel.
More to come...

10
General Discussion / Re: CRG YouTube Channel
« on: May 17, 2013, 06:05:52 PM »
Happy to help you Phil...

11
General Discussion / CRG YouTube Channel
« on: May 17, 2013, 05:10:49 PM »
We are happy to announce that CRG now has a YouTube channel and we have 13 videos on it for your enjoyment.  These videos were made from two different Chevrolet dealer communication kits.

http://www.youtube.com/CamaroResearchGroup

The Camaro video unfortunately is not as complete as I would like it to be.  I have the record, but do not have the film strip and only had most of the frames to be able to piece together what we have now.  If anyone has the film strip and would be willing to let me barrow it, please contact me.  If anyone has another communication kit from 67, 68 or 69, and would like to help us add more videos, let me know.
Enjoy,

12
Decoding/Numbers / Re: 67 Camaro cowl tag and VIN Decoding Help
« on: May 15, 2013, 01:42:05 PM »
Matt,
  Your car also came with a 3-speed stick on the column.  Not many of those around anymore.

13
Decoding/Numbers / Re: 1967 RS Camaro
« on: February 06, 2013, 02:25:02 PM »
Actually the car should not have a a front bumble bee stripe at all.  The car is too early for that.  It should have white pin stripes down the sides.  Here is an ad from Dec 1966 that shows the different models.

I would ether leave the powerglide, or swap it for a TH2004R.  The TH2004R is an over drive trans (the TH350 is not) and is the same size (no need to shorten the drive shaft), but it will need another cross member to mount it.

14
Originality / Re: 1967 Small Journal 350
« on: August 02, 2011, 07:39:02 PM »
Yes, you can get the pan off without pulling the engine.  I don't rmember what I had to do exactly, but I had my pan off several years ago.

15
Originality / Re: 1967 Small Journal 350
« on: July 28, 2011, 05:59:44 PM »
EJ,
  First thanks for the data you have posted, it always helps to see what you have. 
The revision date on that document you mentioned (Jan 1967) was because the L35 engine was added to the document, not because of a change to the L48.  I have a Chevy parts catalog dated Oct 1, 1966 and the 350 crank assembly listed has only one part number (3912355) and no cost listed.  This is the same assembly listed in the Chevy parts catalogue #691A for 67 and 68 350 engines.  I also have all of the 67 model year Chevy dealer service bulletins and they donít list any changes for the 350 crank.  I have all of the Chevy Service News publications for 67 and they donít show any changes to the 350 crank.
My 67 Camaroís engine code is V1209MV.  I have never had the bottom end apart, so I donít know what I have.  If I have a reason to take it apart, I will check into what the crank is, but I really donít expect anything different than what is listed as stock.
You can email me any pictures you like at the higher resolution.
Daniel

Pages: [1] 2 3 ... 11