Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - WaltZ

Pages: [1] 2 3 ... 11
1
General Discussion / Re: Crossram air Filters air flows
« on: January 20, 2023, 02:47:05 PM »
thanks, would you happen to know the K&N number.
much appreciated.

2
General Discussion / Crossram air Filters air flows
« on: January 19, 2023, 04:52:40 PM »
is there an after-market Crossram inexpensive 2.5" tall air filter available.

does not need to be show quality or replicated.

I have a couple of the 1.75" tall $25.00 filters but unsure about inadequate air flow when I get on it.
or, maybe I'm ok with 1.75" talls
Any thoughts will be appreciated.
Thanks in Advance,
Walt

3
General Discussion / Re: New library of documentation page
« on: January 16, 2023, 06:29:08 PM »
Great and very useful info.
Thank you for your time and effort to share this with everyone.

4
2131 HKR
replaced recall lift kit with this one I fabricated

5
installed Hooker Super Comp Headers #2131HKR on my 69 Z with power steering.
Fit pretty well with a minor pinch for the pitman arm screw and nut and another minor pinch for steering box clearance.
Pinched done with a block and a hd C clamp.
Factory Lock Out linkage no alterations needed and plenty of clearances.
The head shields went back on also.
By now, you think hooker would supply the 3/8 x 5/16 head header bolts instead of the 3/8 x 3/8. added another $25.00 with shipping for arps for 6pt heads
And why can't they have the necessary bends or pinches so they can just be installed with no alterations.
Otherwise, Happy with them!
Pictures are before I changed out the header bolts to the 5/16 heads.

6
General Discussion / Crossram under std cowl hood
« on: November 19, 2022, 04:32:09 PM »
Just wondering if the cross ram will work with the std (round hole) cowl hood.
Or does anyone know of modifications that can be made the hood to accept the crossram.
Not too crazy about modifying an original cowl hood, but I will on my aftermarket one.
Any ideas or recommendations will be appreciated.
Thanks in Advance,
Walt

7
Decoding/Numbers / Re: Pad Stamp Tonawanda L48
« on: October 29, 2022, 05:11:55 PM »
thanks Ed, looking foward you your thoughts and insights. The  previous owner had it in his garage for over 40 years and believed it to be from a ss 350 camaro, but who really knows. thanks

8
Decoding/Numbers / Pad Stamp Tonawanda L48
« on: October 29, 2022, 03:22:41 PM »
This 4 bolt large journal short block is in good shape, std bore, original 3.48 crank, rods pistons and turns over smoothly
before i dismantle it and send out for cleaning and magnafluxing, I'd like to know what the vin #s might mean
TI004HN:
Tonawanda, October 4, 1968, 300 hp 350ci, 350 turbo hydromantic.
 ... the 00 are not the same?, I have heard of similar differences on other Tonawanda blocks including an I used as a 1.

the vin numbers are what I can't' figure out.
naked eye looks like: 19201276
with photo enhancement, the 9 may be a 3, the 0 may be a 9, if so: 13291276
please see picture.
any help is appreciated.
and thank you in advance,
Walt

9
General Discussion / 69 Z28 oil pan, repop?
« on: October 26, 2022, 11:33:51 PM »
does anyone make a reproduction 69z28 oil pan with oe style rails and baffles.
thanks in advance,
Walt

10
Garage Talk / Re: Vintage O2 Engine analyzer parts or repairs
« on: October 19, 2022, 11:24:14 PM »
thanks Ed.

11
Garage Talk / Vintage O2 Engine analyzer parts or repairs
« on: October 19, 2022, 05:03:44 PM »
Looking recommendations for parts or someone who can repair a vintage exhaust gas analyzer.
The O2 sensor in the sensing unit box is bad.
Peerless Part # HA 8210 A, but this unit is also used with the Stewart Warner, Sears Penske and some Sun Analyzers.
Meter unit is good.

Hoping there's another O2 sensor that can be used with this meter.

Thank in Advance,
Walt

12
General Discussion / Crossram and headers
« on: August 25, 2022, 01:56:12 PM »
anyone running a crossram with headers on the street cruising with 302 and 30/30 cam.
jettting:
font carb p65s and s68s
rear carb p71s and s75s
any thoughts on this.
thanks in advance,
Walt

13
General Discussion / R44F plugs?
« on: August 04, 2022, 04:05:41 PM »
currently running ACDelco R44s and no issues,,,
hard to find these anymore so what does the F on R44F mean and are they compatible for a 69, back to stock, 302.
Thanks in advance.

14
Maintenance / Re: At a loss - engine stalls under load
« on: July 19, 2022, 05:07:44 PM »
Just throwing this out there.
After the floats checked, try increasing the squirter size +2 and test for any difference in stumble,
if it's better, then try the next accelerator cam up, try again and if the stumble is lessening, try the next couple of cams.
Had this stumbling and sometimes stalling issue with my stock 302 and when bumping up the accelerator cam, it took care of the stumble and stalling, therefore it was starving for fuel during load and acceleration by the pump cam curve not being enough.
It may be a good idea read and understand how these cams can affect your performance, for better or for worse.
Been thru it and I know your frustrations. Sometimes it just the simple checks we overlook.
Good Luck

15
Great replies and pictures. not sure when I will get to this, but when I do, I'll be sure to post the updated steps I uses to accomplish this.
I am still deciding on which headers to use, I would prefer to use the 1968 Z28 headers as first posted. 

Pages: [1] 2 3 ... 11
anything