CRG Discussion Forum
Camaro Research Group Discussion => Originality => Topic started by: GaryL on March 01, 2010, 02:27:11 AM
-
Does anyone have pictures of original '69 tail pipes? I would like to see them on a car from side shot and maybe off the car too. The repros seem to be bent wrong. They angle down slightly when they have proper clearance for the rear bracket to frame and I can't get the .625" measurement to the rear body valence with the pipes level. Any help would be appreciated. They also may be a bit too long and stick out too far.
-
If you don't get a reply, send me an e-mail at jiaccino@cox.net & I'll take some pictures of mine. Az car, 150k & still all original exhaust
Joe
-
Thanks Joe!
-
The exhaust system is one of the few things on my '69 Z/28 that isn't orginal; the previous (original) owner had it replaced about 20 years ago with a stainless system, but the tailipipes appear to be pretty close to the original configuration - photo below.
-
Try www.gardnerexhaust.com They seem to know what their doing!! Ill be buying my exhaust from them!
-
Try www.gardnerexhaust.com They seem to know what their doing!! Ill be buying my exhaust from them!
Not any longer. Ask Pacecarjeff. I just want to get my tailpipes tweaked to sit level, not buy a new set.
The right side is worse than the left, but you can see they angle down. I can't get it higher because the rear bracket gets too close to the frame.
-
Gary. I sent you an e-mail with pictures...Joe
-
Thanks Joe and John.
-
Can I get pics too? Do they go straight out and level? The set on my car (from Ricks) goes to the sides a little.
-
Nice ride GaryL.
-
Kevin
Send me an e-mail at jiaccino@amphi.com. I'll send you the same pictures I sent Gary.....Joe
-
Try www.gardnerexhaust.com They seem to know what their doing!! Ill be buying my exhaust from them!
There is a dilemma with them. More here: http://www.camaros.org/forum/index.php?topic=6180.msg40508#msg40508
-
Can I get pics too? Do they go straight out and level? The set on my car (from Ricks) goes to the sides a little.
I had that same problem with the tailpipes I got from HBC. They just could neot get it right 2 times. I used the D&R pipes and they look very close to Kevin's pictures. They are supposed to go straight out and level. I need to tweak mine a little.
Thanks L78 steve.
-
Can I get pics too? Do they go straight out and level? The set on my car (from Ricks) goes to the sides a little.
I had that same problem with the tailpipes I got from HBC. They just could neot get it right 2 times. I used the D&R pipes and they look very close to Kevin's pictures. They are supposed to go straight out and level. I need to tweak mine a little.
Thanks L78 steve.
-
Back in 2005 I installed a stainless exhaust system from the Stainless Works; purchased through Summit Racing. I've been pleased witht he fit. The last section of both tailpipes are chromed, not original, but a very nice look.
-
Take them to a muffler shop & put a little more bend in them!
-
Take them to a muffler shop & put a little more bend in them!
That is my plan. Just wanted to see what they should look like.
-
Kevin
Send me an e-mail at jiaccino@amphi.com. I'll send you the same pictures I sent Gary.....Joe
Joe email on the way.
Once I fix all the other issues on my car the tailpipe tweak will be next, I am pretty sure they need to be bent parallel and up a bit. thx
-
They appear to be bent slightly down. Look at old pix and decide for your self.
I have Michael Lamm's book but there are other good references.
-Mark.
-
This is a picture jacmac sent to me. It is original. Looks level to me.
-
To me, it actually looks like it goes up about 1/4 in.
-
here is mine